M25P32-VME6P datasheet(6/39 Pages) STMICROELECTRONICS

Part #	M25P32-VME6P

Description	32 Mbit, Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface

Download	39 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

6 / 39 page

M25P32

6/39

SIGNAL DESCRIPTION

Serial Data Output (Q). This

output

signal is

used to transfer data serially out of the device.

Data is shifted out on the falling edge of Serial

Clock (C).

Serial Data Input (D). This input signal is used to

transfer data serially into the device. It receives in-

structions, addresses, and the data to be pro-

grammed. Values are latched on the rising edge of

Serial Clock (C).

Serial Clock (C). This input signal provides the

timing of the serial interface. Instructions, address-

es, or data present at Serial Data Input (D) are

latched on the rising edge of Serial Clock (C). Data

on Serial Data Output (Q) changes after the falling

edge of Serial Clock (C).

Chip Select (S). When this input signal is High,

the device is deselected and Serial Data Output

(Q) is at high impedance. Unless an internal Pro-

gram, Erase or Write Status Register cycle is in

progress, the device will be in the Standby Power

mode (this is not the Deep Power-down mode).

Driving Chip Select (S) Low enables the device,

placing it in the Active Power mode.

After Power-up, a falling edge on Chip Select (S)

is required prior to the start of any instruction.

Hold (HOLD). The Hold (HOLD) signal is used to

pause any serial communications with the device

without deselecting the device.

During the Hold condition, the Serial Data Output

(Q) is high impedance, and Serial Data Input (D)

and Serial Clock (C) are Don’t Care.

To start the Hold condition, the device must be se-

lected, with Chip Select (S) driven Low.

Write Protect (W). The main purpose of this in-

put signal is to freeze the size of the area of mem-

ory that is protected against program or erase

instructions (as specified by the values in the BP2,

BP1 and BP0 bits of the Status Register).

Similar Part No. - M25P32-VME6P

Manufacturer	Part #	Datasheet	Description
Numonyx B.V	M25P32-VME6P	1,011Kb / 53P	32-Mbit, low voltage, serial Flash memory with 75 MHz SPI bus interface

More results

Similar Description - M25P32-VME6P

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M25P64	375Kb / 49P	64 Mbit, Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface
	M25P64	519Kb / 38P	64 Mbit, Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface
	M25P10-A	392Kb / 49P	1 Mbit, low voltage, Serial Flash memory with 50MHz SPI bus interface
Numonyx B.V	M25P20	962Kb / 50P	2 Mbit, low voltage, Serial Flash memory with 50MHz SPI bus interface
STMicroelectronics	M25P128	303Kb / 41P	128 Mbit (Multilevel), Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface
Numonyx B.V	M25P32	1,011Kb / 53P	32-Mbit, low voltage, serial Flash memory with 75 MHz SPI bus interface
STMicroelectronics	M25P80	563Kb / 41P	8 Mbit, Low Voltage, Serial Flash Memory With 40MHz SPI Bus Interface August 2004
AMIC Technology	A25L16P	510Kb / 38P	16 Mbit, Low Voltage, Serial Flash Memory With 85MHz SPI Bus Interface
AMIC Technology	A25L40P	473Kb / 38P	4 Mbit, Low Voltage, Serial Flash Memory With 85MHz SPI Bus Interface
STMicroelectronics	M25P20	395Kb / 50P	2 Mbit, Low Voltage, Serial Flash Memory With 40MHz SPI Bus Interface

More results

M25P32-VME6P Datasheet(PDF) 6 Page - STMicroelectronics

M25P32-VME6P Datasheet(HTML) 6 Page - STMicroelectronics

Similar Part No. - M25P32-VME6P

Similar Description - M25P32-VME6P

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

Datasheet Download

Link URL