Electronic Components Datasheet Search |
|
XRT82D20IW Datasheet(PDF) 6 Page - Exar Corporation |
|
XRT82D20IW Datasheet(HTML) 6 Page - Exar Corporation |
6 / 27 page áç áç áç áç SINGLE CHANNEL E1 LINE INTERFACE UNIT XRT82D20 REV. 1.0.7 4 12 ATM I Alarm Test Mode (Active-Low): Connect this pin to ground to force ClkLOS, RLOS = 0 and LCV = 1 for testing without affecting data transmission. (internal pull-up) 13 RAOS I Receive All Ones: With this pin tied to High, an all “1’s” signal is inserted to the receiver out- put at RPOS and RNEG/RData using MCLK as timing reference. This control has priority over Digital Loop-back if both are enabled. (internal pull-down). 14 TAOS I Transmit All Ones: With this pin tied High, an AMI encoded all “1’s” signal is sent to the transmit output using MCLK as timing reference. This control has priority over Remote Loop-back if both are enabled. (internal pull-down). 15 MClk I Master Clock Input: This signal is an independent 2.048 MHz clock with accuracy better than + 50 ppM and duty cycle within 40% to 60%. The function of MClk is to provide timing source for the PLL clock recovery circuit, reference clock to insert all “1’s” data in the transmit as well as receive paths. This signal must be available for the device to operate. 16 JATx/Rx (DR/SR) I Jitter Attenuator Path Select: With the jitter attenuator enabled, (pin 18 =”1”), tie this pin “High” to select the jitter attenuator in the transmit path and tie it “Low” to select in the receive path. Data input/output format is then controlled automati- cally by the status of the TNEG input. If TNEG data is present the device operates in Dual-rail data mode. Dual-Rail/Single-Rail Select: With the jitter attenuator disabled, (pin 18 =”0”), tie this pin “High” to select Dual-Rail data format and tie it “Low” to select Single-Rail data for- mat. (internal pull-down) 17 DIGI I Digital Interface: With this pin tied Low, input data at TPOS/TData and TNEG/CODE is active-high and will be sampled by TClk on the falling edge, while active- high RPOS/RData and RNEG output data are updated on the falling edge of RClk. See Figure 3 and 4 for details. With his pin tied high and in Dual-rail mode, transmit input accepts active-low TPOS/TData and TNEG/CODE data and will be sampled by TClk on the falling edge, while RPOS/RData and RNEG/LCV are active- low, data is updated on the rising edge of RClk. (internal pull-down). 18 JAEN I Jitter Attenuator Enable (active high): Connect this pin high to enable the jitter attenuation function. Jitter Atten- uator Path select is determined by the pin 16 setting. (internal pull-down) 19 TGND - Transmitter Supply Ground 20 TRing O Transmitter Ring Output: Negative bipolar data output to the line. 21 TVDD - Transmit Positive Supply: 5.0 V + 5% or 3.3 V + 5% 22 TTIP O Transmitter TIP Output: Positive bipolar data output to the line. 23 TxLEV I Transmit Level: Tie this pin high for 120 Ω twisted pair cable operation and tie it low for 75 Ω coaxial cable operation (internal pull-down). This pin is only active for 5.0V operation. PIN #SYMBOL TYPE DESCRIPTION |
Similar Part No. - XRT82D20IW |
|
Similar Description - XRT82D20IW |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |