Electronic Components Datasheet Search |
|
LM5034MTC Datasheet(PDF) 3 Page - National Semiconductor (TI) |
|
|
LM5034MTC Datasheet(HTML) 3 Page - National Semiconductor (TI) |
3 / 29 page Pin Description (Continued) PIN NAME DESCRIPTION APPLICATIONS INFORMATION 6 UVLO VIN Under-Voltage Lockout An external resistor divider sets the input voltage threshold to enable the LM5034. The UVLO comparator reference voltage is 1.25V. A switched 20 µA current source provides adjustable UVLO hysteresis. The UVLO pin voltage also controls the maximum duty cycle as described in the Functional Description section. 7 VCC1 Start-up regulator output, Controller 1 Output of the 7.7V high voltage start-up regulator for Controller 1. The sum of the currents drawn from VCC1 and VCC2 should not exceed 19 mA. 8 OUT1 Main Gate Driver, Controller 1 Gate driver output to the primary side switch for Controller 1. OUT1 swings between VCC1 and GND1 at a frequency equal to half the oscillator frequency. 9 AC1 Active Clamp Driver, Controller 1 Gate driver output to the active clamp P-channel MOSFET for Controller 1. The AC1 pulse overlaps the leading and trailing edges of the OUT1 pulse by an interval set by the OVLP pin resistor. The overlap produces deadtime between the main switch transistor and the P-channel active clamp transistor. 10 GND1 Ground, Controller 1 Ground connection for Controller 1 including gate drivers, PWM controller, soft-start and support functions. 11 GND2 Ground, Controller 2 Ground connection for Controller 2 including gate drivers, PWM controller and soft-start. 12 AC2 Active Clamp Driver, Controller 2 Gate driver output to the active clamp P-channel MOSFET for Controller 2. The AC2 pulse overlaps the leading and trailing edges of the OUT2 pulse by an interval set by the OVLP pin resistor. The overlap produces deadtime between the main switch transistor and the P-channel active clamp transistor. 13 OUT2 Main Gate Driver, Controller 2 Gate driver output to the primary side switch for Controller 2. OUT2 swings between VCC2 and GND2 at a frequency equal to half the oscillator frequency. 14 VCC2 Start-up regulator output, Controller 2 Output of the 7.7V high voltage start-up regulator for Controller 2. The sum of the currents drawn from VCC1 and VCC2 should not exceed 19 mA. 15 RES Hiccup mode restart adjust An external capacitor sets the time delay before forced restart during a sustained period of cycle-by-cycle current limiting. The hiccup mode comparator threshold is 2.55V. 16 SS2 Soft-start, Controller 2 An internal 50 µA current source charges an external capacitor to set the soft-start rate. During a current limit restart sequence, the internal current source is reduced to 1µA to increase the delay before retry. Forcing SS2 below 0.5V shuts off Controller 2. 17 CS2 Current Sense Input, Controller 2 Input for current mode control and the current limit sensing. If the CS2 pin exceeds 0.5V the OUT2 pulse is terminated producing cycle-by-cycle current limiting. External resistance connected to CS2 will adjust (increase) PWM slope compensation. This pin’s voltage must not exceed 1.25V. 18 COMP2 PWM Control, Controller 2 The COMP2 input provides voltage feedback to the PWM comparator inverting input of Controller 2 through a 3:1 divider. The OUT2 duty cycle increases as the COMP2 voltage increases. An internal 5k Ω pull-up resistor to +5.0V provides bias current to the opto-coupler transistor. 19 DCL Duty Cycle Limit An external resistor sets the maximum allowed duty cycle at OUT1 and OUT2. 20 RT/SYNC Oscillator Adjust and Synchronizing input An external resistor sets the oscillator frequency. This pin also accepts ac-coupled synchronization pulses from an external source. www.national.com 3 |
Similar Part No. - LM5034MTC |
|
Similar Description - LM5034MTC |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |