Electronic Components Datasheet Search |
|
APW6021KC-TUL Datasheet(PDF) 6 Page - Anpec Electronics Coropration |
|
APW6021KC-TUL Datasheet(HTML) 6 Page - Anpec Electronics Coropration |
6 / 13 page Copyright ANPEC Electronics Corp. Rev. P.4 - Mar., 2001 APW6021 www.anpec.com.tw 6 Functional Pin Description Cont. VID4, VID3, VID2, VID1, VID0 (Pins 3, 4, 5, 6 and 7) VID0-4 are the TTL-compatible input pins to the 5-bit DAC. The logic states of these five pins program the internal voltage reference (DACOUT). The level of DACOUT sets the microprocessor core converter output voltage, as well as the corresponding PGOOD and OVP thresholds. PGOOD (Pin 8) PGOOD is an open collector output used to indicate the status of the output voltages. This pin is pulled low when the synchronous regulator output is not within ±10% of the DACOUT reference voltage or when any of the other outputs are below their under- voltage thresholds. The PGOOD output is open for“11111” VID code. SD (Pin 9) This pin shuts down all the outputs. A TTL- compatible, logic level high signal applied at this pin immediately discharges the soft-start capacitor, disabling all the outputs. Dedicated internal circuitry insures the core output voltage does not go negative during this process. When re-enabled, the IC under- goes a new soft-start cycle. Left open, this pin is pulled low by an internal pull-down resistor, enabling operation. VSEN2 (Pin 10) Connect this pin to the output of the AGP linear regulator. The voltage at this pin is regulated to the level predetermined by the logic-level status of the SELECT pin. This pin is also monitored for under- voltage events. SELECT (Pin 11) This pin determines the output voltage of the AGP bus linear regulator. A low TTL input sets the output voltage to 1.5V, while a high input sets the output voltage to 3.3V. SS (Pin 12) Connect a capacitor from this pin to ground. This capacitor, along with an internal 28 µA current source, sets the soft-start interval of the converter. FAULT / RT (Pin 13) This pin provides oscillator switching frequency adjustment. By placing a resistor (R T) from this pin to GND, the nominal 200kHz switching frequency is in- creased according to the following equation: Fs =200kHz + 5 × 10 6 / R T (kΩ) (R T to GND) Conversely, connecting a resistor from this pin to VCC reduces the switching frequency according to the fol- lowing equation: Fs =200kHz + 4 × 10 7 / R T (kΩ) (R T to 12V) Nominally, the voltage at this pin is 1.26V. In the event of an over-voltage or over-current condition, this pin is internally pulled to VCC. VSEN4 (Pin 14) Connect this pin to the output of the linear 1.8V regulator. This pin is monitored for undervoltage events. DRIVE4 (Pin 15) Connect this pin to the gate of an external MOSFET. This pin provides the drive for the 1.8V regulator’s pass transistor. VAUX (Pin 16) This pin provides boost current for the linear regula- tors’ output drives in the event bipolar NPN transis- tors (instead of N-channel MOSFETs) are employed as pass elements. The voltage at this pin is moni- tored for power-on reset (POR) purposes. GND (Pin 17) Signal ground for the IC. All voltage levels are mea- sured with respect to this pin. |
Similar Part No. - APW6021KC-TUL |
|
Similar Description - APW6021KC-TUL |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |