Electronic Components Datasheet Search |
|
IS61DDB42M18 Datasheet(PDF) 5 Page - Integrated Silicon Solution, Inc |
|
IS61DDB42M18 Datasheet(HTML) 5 Page - Integrated Silicon Solution, Inc |
5 / 26 page Integrated Silicon Solution, Inc. — 1-800-379-4774 5 Rev. B 07/09/04 ISSI® 36 Mb (1M x 36 & 2M x 18) DDR-II (Burst of 4) CIO Synchronous SRAMs The write data is provided in a ‘late write’ mode; that is, the data-in corresponding to the first address of the burst, is presented 1 cycle later or at the rising edge of the following K clock. The data-in corresponding to the second write burst address follows next, registered by the rising edge of K. The third data-out is clocked by the subsequent rising edge of the K clock, and the fourth data-out is clocked by the subsequent rising edge of the K clock. The data-in provided for writing is initially kept in write buffers. The information on these buffers is written into the array on the third write cycle. A read cycle to the last two write address produces data from the write buffers. The SRAM maintains data coherency. During a write, the byte writes independently control which byte of any of the four burst addresses is written (see X18/X36 Write Truth Tables on page 9 and Timing Reference Diagram for Truth Table on page 8). Whenever a write is disabled (R/W is high at the rising edge of K), data is not written into the memory. RQ Programmable Impedance An external resistor, RQ, must be connected between the ZQ pin on the SRAM and VSS to enable the SRAM to adjust its output driver impedance. The value of RQ must be 5x the value of the intended line impedance driven by the SRAM. For example, an RQ of 250 Ω results in a driver impedance of 50Ω. The allowable range of RQ to guarantee impedance matching is between 175 Ω and 350Ω, with the tolerance described in Programmable Impedance Output Driver DC Electrical Characteristics on page 15. The RQ resistor should be placed less than two inches away from the ZQ ball on the SRAM module. The capacitance of the loaded ZQ trace must be less than 3 pF. The ZQ pin can also be directly connected to VDDQ to obtain a minimum impedance setting. ZQ must never be connected to VSS. Programmable Impedance and Power-Up Requirements Periodic readjustment of the output driver impedance is necessary as the impedance is greatly affected by drifts in supply voltage and temperature. At power-up, the driver impedance is in the middle of allowable impedances values. The final impedance value is achieved within 1024 clock cycles. Clock Consideration This device uses an internal DLL for maximum output data valid window. It can be placed in a stopped-clock mode to minimize power and requires only 1024 cycles to restart. No clocks can be issued until VDD reaches its allowable operating range. Single Clock Mode This device can be also operated in single-clock mode. In this case, C and C are both connected high at power-up and must never change. Under this condition, K and K control the output timings. Either clock pair must have both polarities switching and must never connect to VREF, as they are not differ- ential clocks. |
Similar Part No. - IS61DDB42M18 |
|
Similar Description - IS61DDB42M18 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |