Electronic Components Datasheet Search |
|
275U824R103A1A1 Datasheet(PDF) 2 Page - CTS Corporation |
|
275U824R103A1A1 Datasheet(HTML) 2 Page - CTS Corporation |
2 / 6 page Electrical and Mechanical Specifications (continued) All Other Mounts Standard: Twist tab (designated by “1”) Special: Bend tab — 2 or 3 ears Bracket mounted Suggested Panel for Twist Tab .042" thick (1.07mm) Locating Lugs (Bushing Mount) Standard: .312" (7.9mm) radius from center of control. Special: .375" (9.53mm) radius from center of control. Standard Position: Left side supplied unless otherwise specified. Other Positions: Available with lug right side, without lugs, or with lugs both left and right sides. Water Seal Construction Controls are also available to prevent water from entering the control through either the O.D. of shaft and/or the bushing. Shaft and Bushing Information Bushing Lengths Available Standard: .187" or .250" (4.75mm or 6.35mm) Special: .125" increments (3.2mm increments) Thread Size Standard: 1/4" – 32 3/8" – 32 M7 x .75 M8 x .75P Special: As required Molded Shafts Available (Shown with preferred diameter bushing) Bushing Mounted or Ear Mounted Metal Shafts Available (Shown with preferred diameter bushing) Single or Dual Units Concentric Tandem Units Available in two combinations: A – .125" (3.2mm) diameter rear shaft .250" (6.35mm) panel shaft (3/8 – 32 or M9X.75) B – .156" (4.0mm) diameter rear shaft .236" (6.0mm) diameter panel shaft (3/8 – 32 or M8X.75) Most metal shaft diameters can be used with twist tab mountings. With bracket mount, only .187 diameter shafts are used, with turn-down available to obtain smaller diameters. Metal Lengths: Minimum .125" (3.2mm) beyond bushing; special lengths as required. Trims: Plain round screwdriver slotted, flatted, knurled. Other trims available upon request. Molded Flatted and knurled with screwdriver slot available in many lengths and diameters. Terminal Information Standard: T Solder lug formed 90° to the rear. Special: (See below) T: Solder lug perpendicular to shaft. T: Solder lug formed 60° to the rear. U: PC terminals formed 90° forward toward mounting surface. Terminals extend .187" (4.7mm) beyond mounting surface. V: PC terminals formed 90° to the rear, away from panel mounting. Terminals extend .520" (13.2mm) from mounting surface. W: Wire wrap terminals — .156" (4.0mm) terminal extension beyond base, formed 60° to the rear. BX: PC terminals standard .438" (11.1mm) from center line of control to PC board; straight terminals extend .156" (4.0mm) into PC board. X: PC terminals standard .505" (12.8mm) from center line of control to PC board, with .136" (3.4mm) straight terminal extension beyond PC board standoff. Y: PC terminals standard .602" (15.3mm) from centerline of control to PC board, with .140" (3.5mm) straight terminal extension beyond PC board standoff. (continued on next page) SHAFT DIAMETER BUSHING DIAMETER INCH MM INCH MM .156 4.0 1/4" – 32 M7X.75 .187 4.7 — M7X.75 .236 6.0 3/8" – 32 M8X.75 .250 6.35 3/8" – 32 M9X.75 SHAFT DIAMETER BUSHING DIAMETER INCH MM INCH MM .125 3.2 1/4" – 32 M7X.75 .156 4.0 1/4" – 32 M7X.75 .187 4.7 3/8" – 32 M7X.75 .236 6.0 3/8" – 32 M8X.75 .250 6.35 3/8" – 32 M9X.75 |
Similar Part No. - 275U824R103A1A1 |
|
Similar Description - 275U824R103A1A1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |