Electronic Components Datasheet Search |
|
EM6626TQ64B Datasheet(PDF) 9 Page - EM Microelectronic - MARIN SA |
|
EM6626TQ64B Datasheet(HTML) 9 Page - EM Microelectronic - MARIN SA |
9 / 69 page R EM6626 Copyright © 2005, EM Microelectronic-Marin SA 9 www.emmicroelectronic.com At power on, the voltage regulator starts to follow the supply voltage and triggers the power on reset circuitry, and thus the system reset. The CPU of the EM6626 remains in the reset state for the ‘CPU Reset Delay’, to allow the oscillator to stabilize after power up. The oscillator is disabled during sleep mode. So when waking up from sleep mode, the CPU of the EM6626 remains in the reset state for the CPU Reset Delay, to allow the oscillator to stabilize. During this time, the Oscillation Detection Circuit is inhibited. In active or standby modes, the oscillator detection circuit monitors the oscillator. If it stops for any reason, a system reset is generated. After clock restart the CPU waits for the CPU Reset Delay before executing the first instructions. The oscillation detection circuitry can be inhibited with bit NoOscWD = 1 in register RegVldCntl. At power up, and after any system reset, the function is activated. The ‘CPU Reset Delay’ is 32768 system clocks ( Ck[16] ) long. 4.2 Reset Terminal During active or standby modes the Reset terminal has a debouncer to reject noise. Reset must therefore be active for at least 16 ms (system clock = 32 KHz). When canceling sleep mode, the debouncer is not active (no clock), however, reset passes through an analogue filter with a time constant of typical. 5µs. In this case Reset pin must be high for at least 10 µs to generate a system reset. 4.3 Input Port A Reset Function By writing the OptInpRSel1 and OptInpRSel2 registers it is possible to choose any combination of port A input values to execute a system reset. The reset condition must be valid for at least 16ms (system clock = 32kHz) in active and standby mode. OPTInpRSleep selects the input port A reset function in sleep mode. If set to "1" the occurrence of the selected combination for input port A reset will immediately trigger a system reset (no debouncer) . Reset combination selection (InpReset) is done with registers OptInpRSel1 and OptInpRSel2. Following formula is applicable : InpResPA = InpResPA[0] • InpResPA[1] • InpResPA[2] • InpResPA[3] InpRes1PA[n] InpRes2PA[n] InpResPA[n] 0 0 VSS 0 1 PA[n] 1 0 not PA[n] 1 1 VDD n = 0 to 3 i.e. ; - no reset if InpResPA[n] = VSS. - Don't care function on a single bit with its InpResPA[n] = VDD. - Always Reset if InpResPA[3:0] = 'b1111 igure 6. Input Port A Reset Structure 0 1 MUX 2 3 1 0 VSS PA[3] PA[3] VDD BIT [0] BIT [1] BIT [2] BIT [3] InpResPA InpResPA[3] InpRes2PA[3] InpRes1PA[3] Input Port A Reset Bit[2] Selection Input Port A Reset Bit[1] Selection Input Port A Reset Bit[0] Selection Input Port A Reset Bit[3] Selection Input Reset from Port A |
Similar Part No. - EM6626TQ64B |
|
Similar Description - EM6626TQ64B |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |