 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
MPC5553MVZ132R2 Datasheet(PDF) 11 Page - Freescale Semiconductor, Inc |
|
||||||||||||||||||||||||||||||
MPC5553MVZ132R2 Datasheet(HTML) 11 Page - Freescale Semiconductor, Inc |
|
|
11 / 60 page  Electrical Characteristics MPC5553 Microcontroller Data Sheet, Rev. 0 Preliminary—Subject to Change Without Notice Freescale Semiconductor 11 3.7 Power Up/Down Sequencing Power sequencing between the 1.5-V power supply and VDDSYN or the RESET power supplies is required if the user provides an external 1.5-V power supply and ties VRC33 to ground. To avoid this power sequencing requirement, power up VRC33 within the specified operating range, even if not using the on-chip voltage regulator controller. Refer to Section 3.7.1, “Power Up Sequence (If VRC33 Grounded)” and Section 3.7.2, “Power Down Sequence (If VRC33 Grounded).” Another power sequencing requirement is that VDD33 must be of sufficient voltage before POR negates, so that the values on certain pins are treated as 1s when POR does negate. Refer to Section 3.7.3, “Input Value of Pins During POR Dependent on VDD33.” Although there is no power sequencing required between VRC33 and VDDSYN during power up, for the VRC stage turn-on to operate within specification, VRC33 must not lead VDDSYN by more than 600 mV or lag by more than 100 mV. Higher spikes in the emitter current of the pass transistor will occur if VRC33 leads or lags VDDSYN by more than these amounts. The value of that higher spike in current depends on the board power supply circuitry and the amount of board level capacitance. Furthermore, when all of the PORs negate, the system clock will start to toggle, adding another large increase of the current consumption from VRC33. If VRC33 lags VDDSYN by more than 100 mV, this increased current consumption can drop VDD low enough to assert the 1.5-V POR again. Oscillations are even possible because when the 1.5-V POR asserts, the system clock stops, causing the voltage on VDD to rise until the 1.5-V POR negates again. Any oscillations stop when VRC33 is powered sufficiently. When powering down, VRC33 and VDDSYN do not have a delta requirement to each other, because the bypass capacitors internal and external to the device are already charged. When not powering up or down, VRC33 and VDDSYN do not have a delta requirement to each other for the VRC to operate within specification. Although there are no power up/down sequencing requirements to prevent issues like latch-up, excessive current spikes, etc., the state of the I/O pins during power up/down varies depending on power. Table 7 gives the pin state for the sequence cases for all pins with pad type pad_fc (fast type), and Table 8 for all pins with pad type pad_mh (medium type) and pad_sh (slow type). Table 7. Power Sequence Pin States (Fast Pads) VDDE VDD33 VDD pad_fc (Fast) Output Driver State Comment LOW X X Low Functional I/O pins are clamped to VSS and VDDE VDDE LOW X High VDDE VDD33 LOW High Impedance POR asserted. VDDE VDD33 VDD Functional No POR asserted |
Similar Part No. - MPC5553MVZ132R2 |
|
Similar Description - MPC5553MVZ132R2 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
