WMS7202100S datasheet(6/30 Pages) WINBOND

Part #	WMS7202100S

Description	256-TAP DUAL-CHANNEL NON-VOLATILE DIGITAL

Download	30 Pages

Scroll/Zoom	100%

Manufacturer	WINBOND [Winbond]

Direct Link	http://www.winbond.com

Logo

6 / 30 page

WMS7202

- 6 -

6. PIN DESCRIPTION

TABLE 1 – PIN DESCRIPTION

PIN NAME

PIN NO

I/O

DESCRIPTION

CLK

2

I

Serial Clock pin. Data Shifts in one bit at a time on positive clock

(CLK) edges

CS

1

I

Chip Select pin. When CS is HIGH, WMS7202 is deselected and

the SDO pin is at high impedance, and (unless an internal write

cycle is underway) the device will be in the standby state. CS LOW

enables WMS7202, placing it in the active power mode. It should

be noted that after a power-up, a HIGH to LOW transition on CS is

required prior to the start of any operation.

SDI

3

I

Serial Data Input pin. All opcodes, byte addresses and data to be

written to the registers are input on this pin. Data is latched by the

rising edge of the serial clock.

SDO

13

O

Serial Data Output pin with open-drain output. During a read cycle,

data is shifted out on this pin. Data is clocked out by the falling

edge of the serial clock except for the 1

st bit , which is clocked out

by the falling edge of CS. Also can be used to daisy-chain several

parts.

R/B

6

O

Ready signal with active-LOW, open-drain output, and

acknowledges the completion of commands 2, 4, 5, 6, and 7.

WP

4

I

Hardware Write Protect pin. When active LOW WP prevents any

changes to the present contents except retrieving NVMEM

contents.

VDD

14

-

Power Supply

VSS

5

-

Ground pin, logic ground reference

VA1

12

-

A terminal of potentiometer ‘1’, equivalent to the HI terminal

connection on a mechanical potentiometer

VB1

10

-

B terminal of potentiometer ‘1’, equivalent to the LO terminal

connection on a mechanical potentiometer

VW1

11

O

Wiper terminal of potentiometer ‘1’, equivalent to the wiper terminal

of a mechanical potentiometer

VA2

7

-

A terminal of potentiometer ‘2’, equivalent to the HI terminal

connection on a mechanical potentiometer.

VB2

9

-

B terminal of potentiometer ‘2’, equivalent to the LO terminal

connection on a mechanical potentiometer.

VW2

8

O

Wiper terminal of potentiometer ‘2’, equivalent to the wiper terminal

of a mechanical potentiometer.

Similar Part No. - WMS7202100S

Manufacturer	Part #	Datasheet	Description
Winbond	WMS7202100S	318Kb / 29P	256-TAP NON-VOLATILE DIGITAL POTENTIOMETER
Winbond	WMS7202100S	320Kb / 32P	256-TAP QUAD-CHANNEL NON-VOLATILE DIGITAL POTENTIOMETER

More results

Similar Description - WMS7202100S

Manufacturer	Part #	Datasheet	Description
Winbond	WMS7201	318Kb / 29P	256-TAP NON-VOLATILE DIGITAL POTENTIOMETER
Winbond	WMS7204	320Kb / 32P	256-TAP QUAD-CHANNEL NON-VOLATILE DIGITAL POTENTIOMETER
Texas Instruments	TPL0102-100	591Kb / 24P	[Old version datasheet] 256-TAPS DUAL CHANNEL DIGITAL POTENTIOMETER WITH NON-VOLATILE MEMORY MARCH2011
Maxim Integrated Produc...	MAX5389	2Mb / 13P	Dual, 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometer Rev 1; 4/10
	MAX5387	2Mb / 15P	Dual, 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometer Rev 1; 4/10
	MAX5391	2Mb / 14P	Dual 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometers Rev 1; 4/10
	MAX5392	2Mb / 16P	Dual, 256-Tap, Volatile, Low-Voltage, Linear Taper Digital Potentiometer Rev 1; 4/10
	MAX5386	1Mb / 12P	Dual, 256-Tap, Volatile Low-Voltage Linear Taper Digital Potentiometers Rev 0; 4/09
	MAX5391	2Mb / 13P	Dual 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometers Rev 0; 10/09
	MAX5386	2Mb / 13P	Dual, 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometers Rev 2; 1/10

More results

WMS7202100S Datasheet(PDF) 6 Page - Winbond

WMS7202100S Datasheet(HTML) 6 Page - Winbond

Similar Part No. - WMS7202100S

Similar Description - WMS7202100S

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Datasheet Download

Link URL