WMS7202100P datasheet(8/30 Pages) WINBOND

Part #	WMS7202100P

Description	256-TAP DUAL-CHANNEL NON-VOLATILE DIGITAL

Download	30 Pages

Scroll/Zoom	100%

Manufacturer	WINBOND [Winbond]

Direct Link	http://www.winbond.com

Logo

8 / 30 page

WMS7202

- 8 -

7.3. NON-VOLATILE MEMORY (NVMEM)

Each channel has four NVMEM positions available for storing the output buffer operating mode and

the potentiometer setting. These NVMEM positions can be directly written through the SPI using a

write command (#5) with address and data bytes. Another command (#7) is available that stores the

current output buffer operating mode and potentiometer settings into the selected NVMEM position.

Bit A3 and A2 in the instruction byte decide which NVMEM position is used. (See Table 5)

All potentiometers are loaded with the value stored in the NVMEM position 0 for their respective

channel on power up.

7.3.1 Write Protect of NVMEM

Write-protect ( WP ) disables any changes of current content in the NVMEM regardless of the

commands, except that NVMEM setting can be retrieved using commands 4, 6 of Table 5. Therefore,

Write-Protect ( WP ) pin provides hardware NVMEM protection feature with WP tied to Vss. WP ,

which is active at logic LOW, should be tied directly to VDD if it is not being used.

7.4 FLOW CONTROL

Reading and writing to NVMEM requires an internal access cycle to complete before the next

command can be sent. The following commands have additional flow control using the R/B pin.

Read Tap Register (#2)

Read NVMEM (#4)

Program NVMEM (#5)

Load Tap Register(#6)

Program NVMEM with Tap Register (#7)

The R/B bit will be pulled HIGH when CS goes LOW, and will stay HIGH indicating the chip is ready

to accept another command. After sending one of those commands, the R/B pin should be polled to

determine when the device is ready to accept the additional data.

This flow control can be used on all commands without any performance penalty although it is only

needed on the commands listed above.

Similar Part No. - WMS7202100P

Manufacturer	Part #	Datasheet	Description
Winbond	WMS7202100P	318Kb / 29P	256-TAP NON-VOLATILE DIGITAL POTENTIOMETER
Winbond	WMS7202100P	320Kb / 32P	256-TAP QUAD-CHANNEL NON-VOLATILE DIGITAL POTENTIOMETER

Manufacturer	Part #	Datasheet	Description
Winbond	WMS7201	318Kb / 29P	256-TAP NON-VOLATILE DIGITAL POTENTIOMETER
Winbond	WMS7204	320Kb / 32P	256-TAP QUAD-CHANNEL NON-VOLATILE DIGITAL POTENTIOMETER
Texas Instruments	TPL0102-100	591Kb / 24P	[Old version datasheet] 256-TAPS DUAL CHANNEL DIGITAL POTENTIOMETER WITH NON-VOLATILE MEMORY MARCH2011
Maxim Integrated Produc...	MAX5389	2Mb / 13P	Dual, 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometer Rev 1; 4/10
	MAX5387	2Mb / 15P	Dual, 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometer Rev 1; 4/10
	MAX5391	2Mb / 14P	Dual 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometers Rev 1; 4/10
	MAX5392	2Mb / 16P	Dual, 256-Tap, Volatile, Low-Voltage, Linear Taper Digital Potentiometer Rev 1; 4/10
	MAX5386	1Mb / 12P	Dual, 256-Tap, Volatile Low-Voltage Linear Taper Digital Potentiometers Rev 0; 4/09
	MAX5391	2Mb / 13P	Dual 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometers Rev 0; 10/09
	MAX5386	2Mb / 13P	Dual, 256-Tap, Volatile, Low-Voltage Linear Taper Digital Potentiometers Rev 2; 1/10