 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
X9525V20IZ Datasheet(PDF) 10 Page - Intersil Corporation |
|
||||||||||||||||||||||||||||||
X9525V20IZ Datasheet(HTML) 10 Page - Intersil Corporation |
|
|
10 / 24 page  10 FN8210.1 January 3, 2006 Stops and EEPROM Write Modes Stop conditions that terminate write operations must be sent by the master after sending at least 1 full data byte and receiving the subsequent ACKNOWLEDGE signal. If the master issues a STOP within a Data Byte, or before the X9525 issues a corresponding ACKNOWLEDGE, the X9525 cancels the write operation. Therefore, the contents of the EEPROM array does not change. EEPROM Array Read Operations Read operations are initiated in the same manner as write operations with the exception that the R/W bit of the Slave Address Byte is set to one. There are three basic read operations: Current EEPROM Address Read, Ran- dom EEPROM Read, and Sequential EEPROM Read. Current EEPROM Address Read Internally the device contains an address counter that maintains the address of the last word read incre- mented by one. Therefore, if the last read was to address n, the next read operation would access data from address n + 1. On power-up, the address of the address counter is undefined, requiring a read or write operation for initialization. Upon receipt of the Slave Address Byte with the R/W bit set to one, the device issues an ACKNOWLEDGE and then transmits the eight bits of the Data Byte. The master terminates the read operation when it does not respond with an ACKNOWLEDGE during the ninth clock and then issues a STOP condition (See Figure 14 for the address, ACKNOWLEDGE, and data transfer sequence). It should be noted that the ninth clock cycle of the read operation is not a “don’t care.” To terminate a read oper- ation, the master must either issue a STOP condition during the ninth cycle or hold SDA HIGH during the ninth clock cycle and then issue a STOP condition. Another important point to note regarding the “Current EEPROM Address Read” , is that this operation is not available if the last executed operation was an access to a DCP or the CONSTAT Register (i.e.: an operation using the Device Type Identifier 1010A011 or 1010A010). Immediately after an operation to a DCP or CONSTAT Register is performed, only a “Random EEPROM Read” is available. Immediately following a “Random EEPROM Read” , a “Current EEPROM Address Read” or “Sequential EEPROM Read” is once again available (assuming that no access to a DCP or CONSTAT Register occur in the interim). address address 11 5 bytes 15 7 bytes address = 6 address pointer ends here Addr = 7 Figure 13. Example: Writing 2 bytes to a 16-byte page starting at location 11. 5 bytes 10 10 10 10 S t a r t S t o p Slave Address Data A C K SDA Bus Signals from the Slave Signals from the Master 1 Figure 14. Current EEPROM Address Read Sequence 1 0 0 0 A 0 1 0 X9525 |
Similar Part No. - X9525V20IZ |
|
Similar Description - X9525V20IZ |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
