Electronic Components Datasheet Search |
|
ST16C650A Datasheet(PDF) 10 Page - Exar Corporation |
|
ST16C650A Datasheet(HTML) 10 Page - Exar Corporation |
10 / 52 page ST16C650A xr 2.90V TO 5.5V UART WITH 32-BYTE FIFO REV. 5.0.1 10 2.2 5-Volt Tolerant Inputs The 650A can acccept up to 5V inputs even when operating at 3.3V. Caution: XTAL1 is not 5 volt tolerant. 2.3 Device Reset The RESET input resets the internal registers and the serial interface outputs to their default state (see Figure 13). An active high pulse of longer than 40 ns duration will be required to activate the reset function in the device. 2.4 Device Identification and Revision The ST16C650A provides a Device Identification code and a Device Revision code to distinguish the part from other devices and revisions. To read the identification code from the part, it is required to set the baud rate generator registers DLL and DLM both to 0x00. Now reading the content of the DLM will provide 0x04 for the ST16C650A and reading the content of DLL will provide the revision of the part; for example, a reading of 0x01 means revision A. 2.5 DMA Mode The device does not support direct memory access. The DMA Mode (a legacy term) in this document does not mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of the RXRDY# and TXRDY# output pins. The transmit and receive FIFO trigger levels provide additional flexibility to the user for block mode operation. The LSR bits 5-6 provide an indication when the transmitter is empty or has an empty location(s) for more data. The user can optionally operate the transmit and receive FIFO in the DMA mode (FCR bit-3=1). When the transmit and receive FIFO are enabled and the DMA mode is disabled (FCR bit-3 = 0), the 650A is placed in single-character mode for data transmit or receive operation. When DMA mode is enabled (FCR bit-3 = 1), the user takes advantage of block mode operation by loading or unloading the FIFO in a block sequence determined by the programmed trigger level. In this mode, the 650A sets the TXRDY# pin when the transmit FIFO becomes full, and sets the RXRDY# pin when the receive FIFO becomes empty. The following table shows their behavior. Also see Figures 23 through 28. TABLE 2: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE PINS FCR BIT-0=0 (FIFO DISABLED) FCR BIT-0=1 (FIFO ENABLED) FCR BIT-3 = 0 (DMA MODE DISABLED) FCR BIT-3 = 1 (DMA MODE ENABLED) RXRDY# 0 = 1 byte. 1 = no data. 0 = at least 1 byte in FIFO 1 = FIFO empty. 1 to 0 transition when FIFO reaches the trigger level, or timeout occurs. 0 to 1 transition when FIFO empties. TXRDY# 0 = THR empty. 1 = byte in THR. 0 = FIFO empty. 1 = at least 1 byte in FIFO. 0 = FIFO has at least 1 empty location. 1 = FIFO is full. |
Similar Part No. - ST16C650A |
|
Similar Description - ST16C650A |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |