Electronic Components Datasheet Search |
|
MAX9546 Datasheet(PDF) 4 Page - Maxim Integrated Products |
|
MAX9546 Datasheet(HTML) 4 Page - Maxim Integrated Products |
4 / 12 page Differential Video Interface Chipset 4 _______________________________________________________________________________________ PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Large-Signal Bandwidth VIN = 1VP-P, -3dB 20 MHz Large-Signal Flatness VIN = 1VP-P, ±0.5dB 15 MHz Slew Rate SR 50 V/µs Settling Time (0.1%) tSETTLING 400 ns Power-Supply Rejection Ratio PSRR f = 100kHz, 100mVP-P ripple 30 dB Common-Mode Rejection Ratio CMRR f = 100kHz, 100mVP-P ripple 53 dB LOS Timeout Period tLOS 760 µs AC ELECTRICAL CHARACTERISTICS—MAX9547 (VCC = +8.5V, GND = 0V, RL = 75Ω, ZZT = 75Ω, CL = 50pF, TA = -40°C to +85°C, Typical values are at TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Differential Gain DG 3.8 % Differential Phase DP 0.6 degrees Signal-to-Noise Ratio SNR 5MHz lowpass, 100kHz highpass, VIN = 1VP-P 80 dB 2T Pulse-to-Bar Rating 2T = 250ns, bar time is 18µs, the beginning 3.5% and the ending 3.5% of the bar time is ignored 0.2 % 2T Pulse Response 2T = 250ns 0.25 % Group Delay D/dt At 3.58MHz 10 ns Horizontal Tilt (Note 11) 0.12 % Vertical Tilt (Note 11) 0.26 % AC ELECTRICAL CHARACTERISTICS—MAX9546 Driving MAX9547 (VCC = +8.5V, RL = 220Ω across OUT+ and OUT-, RL = 75Ω (MAX9547), ZZT = 75Ω, TA = -40°C to +85°C. Typical values are at TA = +25°C, unless otherwise noted.) (Note 2) Note 2: All devices are 100% production tested at TA = +25°C. All temperature limits are guaranteed by design. Note 3: Defined as differential output to single-ended input. Note 4: Input is AC-coupled. Note 5: The RC time constant (3Hz) formed by the source resistance (RS) and coupling capacitor (CIN) is usually used for lead compensation of the active clamp. The source resistance is 400Ω max. The clamp should remain stable in this condition. Note 6: Differential mode is measured as (OUT+ - OUT-). Common mode is measured as OUT+ + OUT- 2 Note 7: A fault is when the outputs both sink and source current and the amount of extra current sink or source is greater than 3mA. Note 8: Common-mode balance is measured as 20log((OUT+ - OUT-) / (OUT+ + OUT-)). 2 Note 9: Ground between MAX9546 and MAX9547 can be a ±2V difference. Note 10: A loss-of-signal is when the input video signal of the MAX9547 does not change (cross 100mV level from sync tip) for 10 video lines. Note 11: Input capacitor for this test is 0.33µF. |
Similar Part No. - MAX9546 |
|
Similar Description - MAX9546 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |