Electronic Components Datasheet Search |
|
PTB48502AAH Datasheet(PDF) 6 Page - Texas Instruments |
|
PTB48502AAH Datasheet(HTML) 6 Page - Texas Instruments |
6 / 17 page www.ti.com DEVICE INFORMATION PTB48500 PTB48501 PTB48502 SLTS218C – SEPTEMBER 2003 – REVISED AUGUST 2006 TERMINAL FUNCTIONS TERMINAL DESCRIPTION NAME NO. The positive input supply for the module with respect to –VI. When powering the module from a –48 V telecom +VI(1) 1 central office supply, this input is connected to the primary system ground. The negative input supply for the module, and the 0 VDC reference for the Enable, EN Out, and Sync Out –VI 5 signals. When the module is powered from a +48-V supply, this input is connected to the 48-V Return. VO1 10 The higher regulated power output voltage, which is referenced to the COM node. VO2 6 The lower regulated power output voltage, which is referenced to the COM node. The secondary return reference for the module's two regulated output voltages. It is dc isolated from the input COM 7 supply pins. Using a single resistor, this pin allows VO2 to be adjusted higher or lower than the preset value. If not used, VO2 Adjust 9 this pin should be left open circuit. This is an open-collector (open-drain) positive logic input that enables the module output. This pin is Enable(2) 3 referenced to –VI. A logic 0 at this pin disables the module's outputs, and a high impedance enables the outputs. If not used the pin should be left unconnected. This open-collector output may be used to enable the output of other DC/DC converters in applications where the power-up sequence of the related voltages must be precisely controlled. The output is used principally to EN Out 4 control the startup up of a PTB4851xx module when powering ADSL circuits based on the AC7 chipset. The signal is referenced to –VI, and is active low. It is initially off (high impedance), and turns on when the output voltage, VO1, has risen to its nominal set-point voltage. The signal generated by this pin is designed to be used exclusively with the PTB48510 in AC7 ADSL Sync Out 2 applications. When the Sync Out of this converter is connected directly to the Sync In pin of the PTB48510, both modules will operate at the same switch conversion frequency. (POR: Available to PTB48500 and PTB48501 only.) This pin produces an active-low power-on reset signal that may be used to reset logic circuitry. The output is set low during power up just as the output voltage from VO1 POR(3)/COM(4) 8 starts to rise. It remains low for 10 ms after the voltage at VO1 has reached its nominal set-point voltage. This signal is referenced to the COM node, and has a 3.3-k Ω internal pull-up resistor to V O1. (1) Shaded functions indicate signals that are referenced to –VI. (2) Denotes positive logic: Open = Normal operation, –VI = Outputs Off (3) Denotes negative logic: High = Normal operation, Low = Reset (4) This pin is COM on the PTB48502. 6 Submit Documentation Feedback |
Similar Part No. - PTB48502AAH |
|
Similar Description - PTB48502AAH |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |