Electronic Components Datasheet Search |
|
CAT93C56LI-GT2 Datasheet(PDF) 2 Page - Catalyst Semiconductor |
|
CAT93C56LI-GT2 Datasheet(HTML) 2 Page - Catalyst Semiconductor |
2 / 18 page CAT93C56, CAT93C57 Doc. No. MD-1088 Rev. P 2 © Catalyst Semiconductor, Inc. Characteristics subject to change without notice Absolute Maximum Ratings (1) Parameters Ratings Units Storage Temperature -65 to +150 °C Voltage on Any Pin with Respect to Ground (2) -0.5 to +6.5 V Reliability Characteristics (3) Symbol Parameter Min Units NEND (4) Endurance 1,000,000 Program/ Erase Cycles TDR Data Retention 100 Years D.C. OPERATING CHARACTERISTICS, CAT93C56, Die Rev. G – New Product VCC = +1.8V to +5.5V, TA=-40°C to +85°C unless otherwise specified. Symbol Parameter Test Conditions Min Max Units ICC1 Power Supply Current (Write) fSK = 1MHz, VCC = 5.0V 1 mA ICC2 Power Supply Current (Read) fSK = 1MHz, VCC = 5.0V 500 µA ISB1 Power Supply Current (Standby) (x8 Mode) VIN = GND or VCC, CS = GND ORG = GND 2 µA ISB2 Power Supply Current (Standby) (x16 Mode) VIN = GND or VCC, CS = GND ORG = Float or VCC 1 µA ILI Input Leakage Current VIN = GND to VCC 1 µA ILO Output Leakage Current VOUT = GND to VCC, CS = GND 1 µA VIL1 Input Low Voltage 4.5V ≤ VCC < 5.5V -0.1 0.8 V VIH1 Input High Voltage 4.5V ≤ VCC < 5.5V 2 VCC + 1 V VIL2 Input Low Voltage 1.8V ≤ VCC < 4.5V 0 VCC x 0.2 V VIH2 Input High Voltage 1.8V ≤ VCC < 4.5V VCC x 0.7 VCC + 1 V VOL1 Output Low Voltage 4.5V ≤ VCC < 5.5V, IOL = 2.1mA 0.4 V VOH1 Output High Voltage 4.5V ≤ VCC < 5.5V, IOH = -400µA 2.4 V VOL2 Output Low Voltage 1.8V ≤ VCC < 4.5V, IOL = 1mA 0.2 V VOH2 Output High Voltage 1.8V ≤ VCC < 4.5V, IOH = -100µA VCC - 0.2 V Notes: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. (2) The DC input voltage on any pin should not be lower than -0.5V or higher than VCC + 0.5V. During transitions, the voltage on any pin may undershoot to no less than -1.5V or overshoot to no more than VCC + 1.5V, for periods of less than 20 ns. (3) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. (4) Block Mode, VCC = 5V, 25°C |
Similar Part No. - CAT93C56LI-GT2 |
|
Similar Description - CAT93C56LI-GT2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |