Electronic Components Datasheet Search |
|
PLG1C471MDO1 Datasheet(PDF) 1 Page - Nichicon corporation |
|
PLG1C471MDO1 Datasheet(HTML) 1 Page - Nichicon corporation |
1 / 2 page LG Specifications Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105 °C. Radial lead type : Lead free flow soldering condition correspondence Adapted to the RoHS directive (2002/95/EC). series Item Performance Characteristics Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance tan δ ESR ( 1) Leakage Current ( 2) Characteristics of Temperature Impedance Ratio Endurance Damp Heat Resistance to Soldering Heat Marking –55 to +105 °C 2.5 to 16V 330 to 3900 µF ± 20% at 120Hz, 20°C Not more than value of Standard ratings at 120Hz, 20 °C Not more than value of Standard ratings at 100kHz, 20 °C Not more than value of Standard ratings. After 2 minute's application of rated voltage. 20 °C Z +105 °C / Z+20°C 1.25 (100kHz) Z-55 °C / Z + 20°C 1.25 After 2000 hours' application of rated voltage at 105 °C, capacitors meet the specified value for life characteristics listed at right. After 1000 hours' application of rated voltage at 60 °C 90%RH, capacitors meet the specified value for life characteristics listed at right. To comply with recommended conditions for reflow soldering. Pre-heating shall be done at 150 to 200 °C and for 60 to 180 sec. Peak temp. is 265 °C, within 10 sec. Measurement for solder temperature profile shall be made at a point on the terminal nearest where the terminals protrude through the soldering side of PC board. Navy blue print on the case top. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of initial value ( 3) 130% or less of the initial specified value 130% or less of the initial specified value Initial specified value or less ( 1) ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor. ( 2) Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105 °C. ( 3) Initial value : The value before test of examination of resistance to soldering. Radial Lead Type, Higher Capacitance LF LG Higher Capacitance |
Similar Part No. - PLG1C471MDO1 |
|
Similar Description - PLG1C471MDO1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |