 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
MX29F022TQC-12 Datasheet(PDF) 9 Page - Macronix International |
|
||||||||||||||||||||||||||||||
MX29F022TQC-12 Datasheet(HTML) 9 Page - Macronix International |
|
|
9 / 38 page  9 P/N:PM0556 REV. 0.6, DEC. 09, 1998 MX29F022T/B ERASE RESUME This command will cause the command register to clear the suspend state and return back to Sector Erase mode but only if an Erase Suspend command was previously issued. Erase Resume will not have any effect in all other conditions.Another Erase Suspend command can be written after the chip has resumed erasing. SET-UP AUTOMATIC PROGRAM COMMANDS To initiate Automatic Program mode, A three-cycle com- mand sequence is required. There are two "unlock" write cycles. These are followed by writing the Automatic Pro- gram command A0H. Once the Automatic Program command is initiated, the next WE pulse causes a transition to an active program- ming operation. Addresses are latched on the falling edge, and data are internally latched on the rising edge of the WE pulse. The rising edge of WE also be- gins the programming operation. The system does not require to provide further controls or timings. The de- vice will automatically provide an adequate internally generated program pulse and verify margin. If the program opetation was unsuccessful, the data on Q5 is "1", indicating the program operation of internally exceed timing limit. The automatic programming opera- tion is complete when the data read on Q6 stops tog- gling for two consecutive read cycles and the data on Q7 and Q6 are equivalent to data written to these two bits, at which time the device returns to the Read mode(no program verify command is required). WRITE OPERATION STATUS DATA POLLING-Q7 The MX29F022T/B also features Data Polling as a method to indicate to the host system that the Automatic Program or Erase algorithms are either in progress or completed. While the Automatic Programming algorithm is in operation, an attempt to read the device will produce the complement data of the data last written to Q7. Upon completion of the Automatic Program Algorithm an attempt to read the device will produce the true data last written to Q7. The Data Polling feature is valid after the rising edge of the second WE pulse of the two write pulse sequences. While the Automatic Erase algorithm is in operation, Q7 will read "0" until the erase operation is compete. Upon completion of the erase operation, the data on Q7 will read "1". The Data Polling feature is valid after the rising edge of the secone WE pulse of two write pulse se- quences. The Data Polling feature is active during Automatic Pro- gram/Erase algorithm or sector erase time-out.(see sec- tion Q3 Sector Erase Timer) Q6:Toggle BIT I The MX29F022T/B features a "Toggle Bit" as a method to indicate to the host system that the Auto Program/ Erase algorithms are either in progress or complete. During an Automatic Program or Erase algorithm op- eration, successive read cycles to any address cause Q6 to toggle. The system may use either OE or CE to control the read cycles. When the operation is complete, Q6 stops toggling. After an erase command sequence is written, if the chip is protected, Q6 toggles and returns to reading array data. The system can use Q6 and Q2 together to determine whether a sector is actively erasing or is erase sus- pended. When the device is actively erasing (that is, the Automatic Erase algorithm is in progress), Q6 toggling. When the device enters the Erase Suspend mode, Q6 stops toggling. However, the system must also use Q2 to determine which sectors are erasing or erase-sus- pended. Alternatively, the system can use Q7(see the subsection on Q7:Data Polling). If a program address falls within a protected sector, Q6 toggles for approximately 2us after the program com- mand sequence is written, then returns to reading array data. Q6 also toggles during the erase-suspend-program mode, and stops toggling once the Automatic Program algorithm is complete. The Write Operation Status table shows the outputs for Toggle Bit I on Q6. Refer to the toggle bit algorithmg. INDEX |
Similar Part No. - MX29F022TQC-12 |
|
Similar Description - MX29F022TQC-12 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
