Electronic Components Datasheet Search |
|
L6205D Datasheet(PDF) 8 Page - STMicroelectronics |
|
L6205D Datasheet(HTML) 8 Page - STMicroelectronics |
8 / 21 page L6205 8/21 CIRCUIT DESCRIPTION POWER STAGES and CHARGE PUMP The L6205 integrates two independent Power MOS Full Bridges. Each Power MOS has an Rd- son=0.3ohm (typical value @ 25°C), with intrinsic fast freewheeling diode. Cross conduction protection is achieved using a dead time (td = 1 µs typical) be- tween the switch off and switch on of two Power MOS in one leg of a bridge. Using N Channel Power MOS for the upper transis- tors in the bridge requires a gate drive voltage above the power supply voltage. The Bootstrapped (Vboot) supply is obtained through an internal Oscillator and few external components to realize a charge pump circuit as shown in Figure 3. The oscillator output (VCP) is a square wave at 600kHz (typical) with 10V amplitude. Recommended values/part numbers for the charge pump circuit are shown in Table1. Table 1. Charge Pump External Components Values Figure 3. Charge Pump Circuit LOGIC INPUTS Pins IN1A, IN2A, IN1B and IN2B are TTL/CMOS and µC compatible logic inputs. The internal structure is shown in Fig. 4. Typical value for turn-on and turn-off thresholds are respectively Vthon=1.8V and Vthoff=1.3V. Pins ENA and ENB have identical input structure with the exception that the drains of the Overcurrent and thermal protection MOSFETs (one for the Bridge A and one for the Bridge B) are also connected to these pins. Due to these connections some care needs to be taken in driving these pins. The ENA and ENB in- puts may be driven in one of two configurations as shown in figures 5 or 6. If driven by an open drain (collector) structure, a pull-up resistor REN and a ca- pacitor CEN are connected as shown in Fig. 5. If the driver is a standard Push-Pull structure the resistor REN and the capacitor CEN are connected as shown in Fig. 6. The resistor REN should be chosen in the range from 2.2k Ω to 180KΩ. Recommended values for REN and CEN are respectively 100KΩ and 5.6nF. More information on selecting the values is found in the Overcurrent Protection section. Figure 4. Logic Inputs Internal Structure Figure 5. ENA and ENB Pins Open Collector Driving Figure 6. ENA and ENB Pins Push-Pull Driving TRUTH TABLE X = Don't care High Z = High Impedance Output CBOOT 220nF CP 10nF RP 100 Ω D1 1N4148 D2 1N4148 D2 CBOOT D1 RP CP VS VSA VCP VBOOT VSB D01IN1328 INPUTS OUTPUTS EN IN1 IN2 OUT1 OUT2 L X X High Z High Z H L L GND GND H H L Vs GND HLH GND Vs HHH Vs Vs 5V D01IN1329 ESD PROTECTION 5V 5V OPEN COLLECTOR OUTPUT REN CEN ENA or ENB D02IN1349 5V PUSH-PULL OUTPUT REN CEN ENA or ENB D02IN1350 |
Similar Part No. - L6205D |
|
Similar Description - L6205D |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |