M24M01S-LA6T datasheet(4/19 Pages) STMICROELECTRONICS

Part #	M24M01S-LA6T

Description	1 Mbit Serial I짼C Bus EEPROM

Download	19 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

4 / 19 page

M24M01

4/19

DEVICE OPERATION

The device supports the I2C protocol. This is sum-

marized in Figure 2. Any device that sends data on

to the bus is defined to be a transmitter, and any

device that reads the data to be a receiver. The

device that controls the data transfer is known as

the bus master, and the other as the slave device.

A data transfer can only be initiated by the bus

master, which will also provide the serial clock for

synchronization. The M24M01 device is always a

slave in all communication.

Start Condition

Start is identified by a falling edge of Serial Data

(SDA) while Serial Clock (SCL) is stable in the

High state. A Start condition must precede any

data transfer command. The device continuously

monitors (except during a Write cycle) Serial Data

(SDA) and Serial Clock (SCL) for a Start condition,

and will not respond unless one is given.

Stop Condition

Stop is identified by a rising edge of Serial Data

(SDA) while Serial Clock (SCL) is stable and driv-

en High. A Stop condition terminates communica-

tion between the device and the bus master. A

Read command that is followed by NoAck can be

followed by a Stop condition to force the device

into the Stand-by mode. A Stop condition at the

end of a Write command triggers the internal EE-

PROM Write cycle.

Acknowledge Bit (ACK)

The acknowledge bit is used to indicate a success-

ful byte transfer. The bus transmitter, whether it be

bus master or slave device, releases Serial Data

(SDA) after sending eight bits of data. During the

9th clock pulse period, the receiver pulls Serial

Data (SDA) Low to acknowledge the receipt of the

eight data bits.

Data Input

During data input, the device samples Serial Data

(SDA) on the rising edge of Serial Clock (SCL).

For correct device operation, Serial Data (SDA)

must be stable during the rising edge of Serial

Clock (SCL), and the Serial Data (SDA) signal

must change

only when Serial Clock (SCL) is driv-

en Low.

Memory Addressing

To start communication between the bus master

and the slave device, the bus master must initiate

a Start condition. Following this, the bus master

sends the Device Select Code, shown in Table 2

(on Serial Data (SDA), most significant bit first).

The Device Select Code consists of a 4-bit Device

Type Identifier, and a 2-bit Chip Enable “Address”

(E1, E2). To address the memory array, the 4-bit

Device Type Identifier is 1010b.

Up to four memory devices can be connected on a

single I2C bus. Each one is given a unique 2-bit

code on the Chip Enable (E1, E2) inputs. When

the Device Select Code is received on Serial Data

(SDA), the device only responds if the Chip Enable

Address is the same as the value on the Chip En-

able (E1, E2) inputs.

The 8th bit is the Read/Write bit (RW). This bit is

set to 1 for Read and 0 for Write operations.

If a match occurs on the Device Select code, the

corresponding device gives an acknowledgment

on Serial Data (SDA) during the 9th bit time. If the

device does not match the Device Select code, it

deselects itself from the bus, and goes into Stand-

by mode.

Table 2. Device Select Code 1

Note: 1. The most significant bit, b7, is sent first.

Device Type Identifier

Chip Enable Address

RW

b7

b6

b5

b4

b3

b2

b1

b0

Device Select Code

1

0

1

0

E2

E1

A16

RW

Similar Part No. - M24M01S-LA6T

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M24M01-A125	628Kb / 37P	Automotive 1-Mbit serial IC bus EEPROM with 1 MHz clock February 2014 Rev 4
	M24M01-DF	832Kb / 47P	1-Mbit serial I²C bus EEPROM Rev 14 October 2017
	M24M01-DF	376Kb / 38P	1-Mbit serial I짼C bus EEPROM
	M24M01-DWDW3TP	628Kb / 37P	Automotive 1-Mbit serial IC bus EEPROM with 1 MHz clock February 2014 Rev 4
	M24M01-DWMN3TP	628Kb / 37P	Automotive 1-Mbit serial IC bus EEPROM with 1 MHz clock February 2014 Rev 4

More results

Similar Description - M24M01S-LA6T

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M24M01-R	287Kb / 30P	1 Mbit serial I짼C bus EEPROM
	M24M01-R	429Kb / 37P	1 Mbit serial I짼C bus EEPROM
	M24M01-R	376Kb / 38P	1-Mbit serial I짼C bus EEPROM
	M24M01-R	311Kb / 36P	1 Mbit serial I짼C bus EEPROM
Microchip Technology	25AA1024	561Kb / 34P	1 Mbit SPI Bus Serial EEPROM 2010
STMicroelectronics	M95M01-DF	878Kb / 51P	1-Mbit serial SPI bus EEPROM February 2017 Rev 14
Microchip Technology	25AA1024	591Kb / 30P	1 Mbit SPI Bus Serial EEPROM 2007
	25AA1024_1005	561Kb / 34P	1 Mbit SPI Bus Serial EEPROM 2010
	25AA1024	496Kb / 36P	1 Mbit SPI Bus Serial EEPROM 01/27/15
	25LC1024-ESM	705Kb / 34P	1 Mbit SPI Bus Serial EEPROM 2010

More results

M24M01S-LA6T Datasheet(PDF) 4 Page - STMicroelectronics

M24M01S-LA6T Datasheet(HTML) 4 Page - STMicroelectronics

Similar Part No. - M24M01S-LA6T

Similar Description - M24M01S-LA6T

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Datasheet Download

Link URL