M25P80VMP6T datasheet(7/34 Pages) STMICROELECTRONICS

Part #	M25P80VMP6T

Description	512 Kbit, Low Voltage, Serial Flash Memory With 25 MHz SPI Bus Interface

Download	34 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

7 / 34 page

7/34

M25P05-A

Hold Condition

The Hold (HOLD) signal is used to pause any se-

rial communications with the device without reset-

ting the clocking sequence. However, taking this

signal Low does not terminate any Write Status

Register, Program or Erase cycle that is currently

in progress.

To enter the Hold condition, the device must be

selected, with Chip Select (S) Low.

The Hold condition starts on the falling edge of the

Hold (HOLD) signal, provided that this coincides

with Serial Clock (C) being Low (as shown in Fig-

ure 6).

The Hold condition ends on the rising edge of the

Hold (HOLD) signal, provided that this coincides

with Serial Clock (C) being Low.

If the falling edge does not coincide with Serial

Clock (C) being Low, the Hold condition starts af-

ter Serial Clock (C) next goes Low. Similarly, if the

rising edge does not coincide with Serial Clock (C)

being Low, the Hold condition ends after Serial

Clock (C) next goes Low. (This is shown in Figure

6).

During the Hold condition, the Serial Data Output

(Q) is high impedance, and Serial Data Input (D)

and Serial Clock (C) are Don’t Care.

Normally, the device is kept selected, with Chip

Select (S) driven Low, for the whole duration of the

Hold condition. This is to ensure that the state of

the internal logic remains unchanged from the mo-

ment of entering the Hold condition.

If Chip Select (S) goes High while the device is in

the Hold condition, this has the effect of resetting

the internal logic of the device. To restart commu-

nication with the device, it is necessary to drive

Hold (HOLD) High, and then to drive Chip Select

(S) Low. This prevents the device from going back

to the Hold condition.

Figure 6. Hold Condition Activation

AI02029D

HOLD

C

Hold

Condition

(standard use)

Hold

Condition

(non-standard use)

Similar Part No. - M25P80VMP6T

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M25P80VMP6T	589Kb / 41P	1 Mbit, Low Voltage, Serial Flash Memory With 25 MHz SPI Bus Interface
	M25P80VMP6T	128Kb / 7P	512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface
	M25P80VMP6TG	128Kb / 7P	512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface
	M25P80VMP6TP	128Kb / 7P	512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface

More results

Similar Description - M25P80VMP6T

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M25P05	194Kb / 32P	512 Kbit, Low Voltage, Serial Flash Memory With 20 MHz SPI Bus Interface
Numonyx B.V	M25P05-A	1,001Kb / 52P	512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Numonyx B.V	M25P05-A	1Mb / 52P	512-Kbit, serial flash memory, 50 MHz SPI bus interface
PMC-Sierra, Inc	PM25LV512	94Kb / 24P	512 Kbit / 1 Mbit 3.0 Volt-only, Serial Flash Memory With 25 MHz SPI Bus Interface
STMicroelectronics	M25P10-A	589Kb / 41P	1 Mbit, Low Voltage, Serial Flash Memory With 25 MHz SPI Bus Interface
	M25P80	218Kb / 35P	8 Mbit, Low Voltage, Serial Flash Memory With 25 MHz SPI Bus Interface
	M25PXX	128Kb / 7P	512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface
Silicon Storage Technol...	SST25VF512	281Kb / 23P	512 Kbit SPI Serial Flash
	SST25VF512A	291Kb / 25P	512 Kbit SPI Serial Flash
	SST25VF512	263Kb / 23P	512 Kbit SPI Serial Flash

More results

M25P80VMP6T Datasheet(PDF) 7 Page - STMicroelectronics

M25P80VMP6T Datasheet(HTML) 7 Page - STMicroelectronics

Similar Part No. - M25P80VMP6T

Similar Description - M25P80VMP6T

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Datasheet Download

Link URL