Electronic Components Datasheet Search |
|
M29W008AB100N6T Datasheet(PDF) 3 Page - STMicroelectronics |
|
M29W008AB100N6T Datasheet(HTML) 3 Page - STMicroelectronics |
3 / 30 page 3/30 M29W008AT, M29W008AB Instructions Seven instructions are defined to perform Read Array, Auto Select (to read the Electronic Signa- ture or Block Protection Status), Program, Block Erase, Chip Erase, Erase Suspend and Erase Re- sume. The internal P/E.C. automatically handles all timing and verification of the Program and Erase operations. The Status Register Data Poll- ing, Toggle, Error bits and the RB output may be read at any time, during programming or erase, to monitor the progress of the operation. Instructions are composed of up to six cycles. The first two cycles input a Coded sequence to the Command Interface which is common to all in- structions (see Table 9). The third cycle inputs the instruction set-up command. Subsequent cycles output the addressed data, Electronic Signature or Block Protection Status for Read operations. In or- der to give additional data protection, the instruc- tions for Program and Block or Chip Erase require further command inputs. For a Program instruc- tion, the fourth command cycle inputs the address and data to be programmed. For an Erase instruc- tion (Block or Chip), the fourth and fifth cycles in- put a further Coded sequence before the Erase confirm command on the sixth cycle. Erasure of a memory block may be suspended, in order to read data from another block or to program data in an- other block, and then resumed. When power is first applied or if VCC falls below VL- KO, the command interface is reset to Read Array. The block erase operation can be suspended in order to read from or program to any block not be- ing erased, and then resumed. Block protection provides additional data security. Each block can be separately protected or unpro- tected against Program or Erase on programming equipment. All previously protected blocks can be temporarily unprotected in the application. Bus Operations The following operations can be performed using the appropriate bus cycles: Read (Array, Electron- ic Signature, Block Protection Status), Write com- mand, Output Disable, Stand-by, Reset, Block Protection, Unprotection, Protection Verify, Unpro- tection Verify and Block Temporary Unprotection. See Tables 5 and 6. Command Interface Instructions, made up of commands written in cy- cles, can be given to the Program/Erase Controller through a Command Interface (C.I.). For added data protection, program or erase execution starts after 4 or 6 cycles. The first, second, fourth and fifth cycles are used to input Coded cycles to the C.I. This Coded sequence is the same for all Pro- gram/Erase Controller instructions. The ’Com- mand’ itself and its confirmation, when applicable, are given on the third, fourth or sixth cycles. Any incorrect command or any improper command se- quence will reset the device to Read Array mode. Table 2. Absolute Maximum Ratings (1) Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi- tions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant qual- ity documents. 2. Minimum Voltage may undershoot to –2V during transition and for less than 20ns during transitions. 3. Depends on range. Symbol Parameter Value Unit TA Ambient Operating Temperature (3) –40 to 85 °C TBIAS Temperature Under Bias –50 to 125 °C TSTG Storage Temperature –65 to 150 °C VIO (2) Input or Output Voltage –0.6 to 5 V VCC Supply Voltage –0.6 to 5 V V(A9, E, G, RP) (2) A9, E, G, RP Voltage –0.6 to 13.5 V |
Similar Part No. - M29W008AB100N6T |
|
Similar Description - M29W008AB100N6T |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |