M95640MB6TP datasheet(8/46 Pages) STMICROELECTRONICS

Part #	M95640MB6TP

Description	32 Kbit and 64 Kbit serial SPI bus EEPROMs with high-speed clock

Download	46 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

8 / 46 page

Signal description

M95320, M95640, M95320-x, M95640-x

8/46

2

Signal description

During all operations, VCC must be held stable and within the specified valid range:

VCC(min) to VCC(max).

All of the input and output signals must be held high or low (according to voltages of VIH,

VOH, VIL or VOL, as specified in Table 13 to Table 16). These signals are described next.

2.1

Serial Data output (Q)

This output signal is used to transfer data serially out of the device. Data is shifted out on the

falling edge of Serial Clock (C).

2.2

Serial Data input (D)

This input signal is used to transfer data serially into the device. It receives instructions,

addresses, and the data to be written. Values are latched on the rising edge of Serial Clock

(C).

2.3

Serial Clock (C)

This input signal provides the timing of the serial interface. Instructions, addresses, or data

present at Serial Data Input (D) are latched on the rising edge of Serial Clock (C). Data on

Serial Data Output (Q) changes after the falling edge of Serial Clock (C).

2.4

Chip Select (S)

When this input signal is high, the device is deselected and Serial Data output (Q) is at high

impedance. Unless an internal Write cycle is in progress, the device will be in the Standby

Power mode. Driving Chip Select (S) low selects the device, placing it in the Active Power

mode.

After Power-up, a falling edge on Chip Select (S) is required prior to the start of any

instruction.

2.5

Hold (HOLD)

The Hold (HOLD) signal is used to pause any serial communications with the device without

deselecting the device.

During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data

input (D) and Serial Clock (C) are Don’t Care.

To start the Hold condition, the device must be selected, with Chip Select (S) driven low.

Similar Part No. - M95640MB6TP

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M95640MN	164Kb / 19P	64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock

More results

Similar Description - M95640MB6TP

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M95320	353Kb / 44P	32 Kbit and 64 Kbit Serial SPI bus EEPROMs with high speed clock
	M95320	388Kb / 44P	32 Kbit serial SPI bus EEPROMs with high-speed clock
	M95640-A125	802Kb / 44P	Automotive 64-Kbit serial SPI bus EEPROMs with high-speed clock January 2016 Rev 9
	M95320-A125	792Kb / 43P	Automotive 32-Kbit serial SPI bus EEPROMs with high-speed clock February 2016 Rev 8
	M95256-A125	798Kb / 44P	Automotive 256-Kbit serial SPI bus EEPROMs with high-speed clock January 2016 Rev 8
	M95512-A125	799Kb / 44P	Automotive 512-Kbit serial SPI bus EEPROMs with high-speed clock January 2016 Rev 8
	M95640-W	905Kb / 53P	64-Kbit serial SPI bus EEPROM with high-speed clock Rev 19 February 2016
	M95320-W	412Kb / 48P	32-Kbit serial SPI bus EEPROM with high-speed clock
	M95080	164Kb / 19P	64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock
	M95640	164Kb / 19P	64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock

More results

M95640MB6TP Datasheet(PDF) 8 Page - STMicroelectronics

M95640MB6TP Datasheet(HTML) 8 Page - STMicroelectronics

Similar Part No. - M95640MB6TP

Similar Description - M95640MB6TP

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Datasheet Download

Link URL