Electronic Components Datasheet Search |
|
280105-02 Datasheet(PDF) 3 Page - Vishay Siliconix |
|
280105-02 Datasheet(HTML) 3 Page - Vishay Siliconix |
3 / 9 page Document Number: 37026 Revision 05-Dec-00 www.vishay.com 4 TIP-3526PCS-8 Vishay Dale COMMANDS (Code sent to touch panel) COMMAND Automatic baud rate selection (ignored when baud rate is jumper selected) DC1, Ctl Q, XON Software Handshaking DC3, Ctl S, XOFF Software Handshaking *Enable touch panel Disable touch panel (stop scanning) Enable CONTINUOUS/disable TRACKING mode *Disable CONTINUOUS and TRACKING mode Enable TRACKING/disable CONTINUOUS mode Enable ENTER point mode *Disable ENTER point mode Enable EXIT point mode *Disable EXIT point mode Enable automatic report transfer *Disable automatic report transfer (scan but no report) Enable beeper *Disable beeper Failed beam time-out, t = duration (0 to F) (default = 1) *Normal X Invert X *Normal Y Invert Y Reset touch panel Request one coordinate report Request failed beam report Request model number Request software revision number Request touch matrix size Sound beeper, tt = duration (00 to FF) CODE (ASCII) CR DC1 DC3 & ' $ % 4 " # SP ! ) * - . : 6 7 8 9 . + ( 5 0 3 / CODE (HEX) 0D 11 13 26 27 24 25 34 22 23 20 21 29 2A 2D 2E 3At 36 37 38 39 2C 2B 28 35 30 33 2Ftt *Indicates default condition. COMMAND/RESPONSE DESCRIPTION Automatic Baud Rate Selection (0D) For most applications a jumper selected baud rate is recommended. If automatic baud rate selection is required, contact the factory for assistance. (The autobaud command will be ignored if a specific baud rate is jumper selected.) DC1, Ctl Q, XON Software Handshaking (11) DC3, Ctl S, XOFF Software Handshaking (13) RS-232 flow control is provided by these commands. Note: A shunt must be placed on Jumper A (SOFTHAND) to allow software handshaking. Absence of a shunt requires hardware handshaking. (See also ENABLE TOUCH PANEL command.) *Enable Touch Panel (26) Disable Touch Panel (stop scanning) (27) The touch panel must be enabled for normal operation. When the touch panel is disabled, commands are processed as they are received, allowing changes in modes of operation, but discarding any report operations. This differs from XON/XOFF software handshaking. When the touch panel receives an XOFF character (13), commands are executed until the touch panel requires transmission of a report, then all commands received are buffered and are not executed until an XON character is received. If the buffer becomes full, the touch panel sends XOFF. Enable CONTINUOUS/disable TRACKING mode (24) *Disable CONTINUOUS/disable TRACKING mode (25) This coordinate reporting mode will continuously report the coordinates of a stylus that remains in the touch panel. This mode can be used individually or in combination with ENTER point, or EXIT modes. The following report format is used. If more than one stylus enters the touch panel, a non-contiguous report will be generated. 41 = start of coordinate report xx yy = binary X and Y, > = 0, X, Y = FE if non-contiguous |
Similar Part No. - 280105-02 |
|
Similar Description - 280105-02 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |