MC54/74HC4066A

High–Speed CMOS Logic Data

DL129 — Rev 6

3

MOTOROLA

Sb l

P

T

C

di i

V

Guaranteed Limit

Ui

Symbol

Parameter

Test Conditions

VCC

V

– 55 to

25

_C

v 85_C

v 125_C

Unit

Ron

Maximum “ON” Resistance

Vin = VIH

VIS = VCC to GND

IS v 2.0 mA (Figures 1, 2)

2.0†

3.0†

4.5

9.0

12.0

—

—

120

70

70

—

—

160

85

85

—

—

200

100

100

Ω

Vin = VIH

VIS = VCC or GND (Endpoints)

IS v 2.0 mA (Figures 1, 2)

2.0

3.0

4.5

9.0

12.0

—

—

70

50

30

—

—

85

60

60

—

—

100

80

80

∆Ron

Maximum Difference in “ON”

Resistance Between Any Two

Channels in the Same Package

Vin = VIH

VIS = 1/2 (VCC – GND)

IS v 2.0 mA

2.0

4.5

9.0

12.0

—

20

15

15

—

25

20

20

—

30

25

25

Ω

Ioff

Maximum Off–Channel Leakage

Current, Any One Channel

Vin = VIL

VIO = VCC or GND

Switch Off (Figure 3)

12.0

0.1

0.5

1.0

µA

Ion

Maximum On–Channel Leakage

Current, Any One Channel

Vin = VIH

VIS = VCC or GND

(Figure 4)

12.0

0.1

0.5

1.0

µA

†At supply voltage (VCC) approaching 3 V the analog switch–on resistance becomes extremely non–linear. Therefore, for low–voltage

operation, it is recommended that these devices only be used to control digital signals.

NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

Sb l

P

V

Guaranteed Limit

Ui

Symbol

Parameter

VCC

V

– 55 to

25

_C

v 85_C

v 125_C

Unit

tPLH,

tPHL

Maximum Propagation Delay, Analog Input to Analog Output

(Figures 8 and 9)

2.0

3.0

4.5

9.0

12.0

40

30

5

5

5

50

40

7

7

7

60

50

8

8

8

ns

tPLZ,

tPHZ

Maximum Propagation Delay, ON/OFF Control to Analog Output

(Figures 10 and 11)

2.0

3.0

4.5

9.0

12.0

80

60

20

20

20

90

70

25

25

25

110

80

35

35

35

ns

tPZL,

tPZH

Maximum Propagation Delay, ON/OFF Control to Analog Output

(Figures 10 and 1 1)

2.0

3.0

4.5

9.0

12.0

80

45

20

20

20

90

50

25

25

25

100

60

30

30

30

ns

C

Maximum Capacitance

ON/OFF Control Input

—

10

10

10

pF

Control Input = GND

Analog I/O

Feedthrough

—

—

35

1.0

35

1.0

35

1.0

NOTES:

1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

2. Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

C

P

Di

i

i

C

i

(P

S i h) (Fi

13)*

Typical @ 25

°C, VCC = 5.0 V

F

CPD

Power Dissipation Capacitance (Per Switch) (Figure 13)*

15

pF

* Used to determine the no–load dynamic power consumption: PD = CPD VCC2f + ICC VCC. For load considerations, see Chapter 2 of the

Motorola High–Speed CMOS Data Book (DL129/D).