LV1145B LVDS Series

6 Pad Leadless Surface Mount Oscillator

Low Voltage Differential Signal Output with Enable/Disable

1.50 MHz

–

650.00 MHz

Standard Specifications

Overall Frequency Stability

± 50 PPM, ± 25 PPM and ± 20 PPM over Operating Temp. Range

Operating Temperature Range

0 to +80°C is standard, can be extended to - 40 to +85°C

Operable Supply Voltage (Vcc) 3.3 V ± 5% standard, 5.0 V ± 10% also available

Part Numbering Guide

1.43 V typical and 1.60 V maximum with output enabled (100 ohm load) See Test circuit #6

0.90 V minimum and 1.10 V typical with output enabled (100 ohm load) See TC #6

High Level Output Voltage

Low Level Output Voltage

Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.

Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load

(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com

5

Pl tronics, Inc.

Model

Frequency Stability

45 = ± 50 PPM

LV11 = E/D Pin 2

LV33 = E/D Pin 1 & 2

LV37 = E/D Pin 1

44 = ± 25 PPM

Frequency in MHz

Special Specifications (choose all that apply)

LV11 45 B V - 70.0M - XXX (Internal Code or blank)

20 = ± 20 PPM

Output Leakage Current

10 uA maximum with output disabled

Differential Output Voltage

Offset Voltage

247 V minimum, 330 V typical and 454 V maximum with output enabled (100 ohm load) See TC #6

1.125 V minimum, 1.25 V typical and 1.375 V maximum with output enabled (100 ohm load) See TC #6

50 mA max < 200 MHz, 60 mA max < 500 MHz, 70 mA max 500 MHz and above

20 mA max < 200 MHz, 30 mA max < 500 MHz, 40 mA max 500 MHz and above

Supply Current (Icc) Enabled

0.7 Vcc minimum at Enable / Disable Pin

0.3 Vcc maximum at Enable / Disable Pin

High Level Input Voltage

Low Level Input Voltage

Output Enable Time

200 nS maximum

High Level Input Current

Low Level Input Current

-20 uA maximum at Enable / Disable Pin = 0.7 Vcc

-200 uA maximum at Enable / Disable Pin = 0 V

200 nS maximum

Output Disable Time

Supply Current (Icc) Disabled

RMS Jitter

Enable / Disable Pin:

1.0 pS max at12 kHz to 20 MHz from the output

Symmetry (DC)

Rise and Fall Time (Tr & Tf)

45/55% measured at 0°C <= Ta <= 70°C, 40/60% measured at Ta < 0°C and Ta > 70°C

1.0 nS max at 20% to 80% output swing (100 ohm load) See Test circuit #6 and Waveform #2

Packaging

Tube or

24mm tape

16mm pitch

Consult factory for higher frequencies

Pl tronics, Inc.

19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA

Manufacturer of High Quality Frequency Control Products

.

Portions of the part number that appear after the frequency may not be marked on part (C of C provided)

Jun 2004

The Enable / Disable pin has an internal pull up and if the pin is not connected the oscilaltor is enabled. Pletronics strongly recommends

connecting the Enable / Disable pin to Vcc, if the oscillator is to be enabled at all times. In the disable condition, the output becomes a

high impedance.