Electronic Components Datasheet Search |
|
MPDTH05010WAS Datasheet(PDF) 2 Page - Murata Manufacturing Co., Ltd. |
|
MPDTH05010WAS Datasheet(HTML) 2 Page - Murata Manufacturing Co., Ltd. |
2 / 6 page MPDTH_10 Series.A04 Page 2 of 6 Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 www.murata-ps.com MPDTH***10 Series Adjustable Non-isolated 12/15-Amp POLA DC/DC Converters SPECIFICATION SUMMARY AND ORDERING GUIDE Output Input (9) Vout Iout (Amps, Power Ripple&Noise Regulation Vin nom. Range Efficiency Package Model Number (Volts) max.) (Watts) (mV pk-pk) Line Load (Volts) (Volts) (%) Case(inches) Case(mm) Type(2) MPDTH03010WAH 0.8-2.5 15 37.5 20(6) ±1.25% ±1.5% 3.3 3-3.6 93(3) 1.37x0.62x0.35 34.80x15.75x9.0 TH MPDTH03010WAS 0.8-2.5 15 37.5 20(6) ±1.25% ±1.5% 3.3 3-3.6 93(3) 1.37x0.62x0.38 34.80x15.75x9.57 SM MPDTH05010WAH 0.8-3.6 15 54 30(7) ±1.25% ±1.5% 5.0 4.5-5.5 95(4) 1.37x0.62x0.35 34.80x15.75x9.0 TH MPDTH05010WAS 0.8-3.6 15 54 30(7) ±1.25% ±1.5% 5.0 4.5-5.5 95(4) 1.37x0.62x0.38 34.80x15.75x9.57 SM MPDTH12010WAH 1.2-5.5 12 66 33(8) ±1.25% ±1.5% 12.0 10.8-13.2 94(5) 1.37x0.62x0.35 34.80x15.75x9.0 TH MPDTH12010WAS 1.2-5.5 12 66 33(8) ±1.25% ±1.5% 12.0 10.8-13.2 94(5) 1.37x0.62x0.38 34.80x15.75x9.57 SM Input Input Voltage Range See Ordering Guide Start-Up Voltage 2.45 Volts (MPDTH03010) 4.3 Volts (MPDTH05010) 9.5 Volts (MPDTH12010) Undervoltage Shutdown 2.4 Volts (MPDTH03010) 3.7 Volts (MPDTH05010) 9.0 Volts (MPDTH12010) External Input Capacitor (See note 3) 470 μF, required (MPDTH03010 and MPDTH05010) 560 μF required (MPDTH12010) Remote On/Off Inhibit Control Positive Logic Inhibit Current (grounded) OFF = -0.2V to +0.8 V max. or ground pin ON = open pin (internal pullup) to +Vin -130 μA (MPDTH03010 and MPDTH05010) [5] -240 μA (MPDTH12010) [5] Tracking Input Current when grounded Slew rate Tracking Input Range -130 μA 1 Volt per mSec max. -0.3V to (+Vin + 0.3V) Margin Controls -5% or +5% adjustment of Vout when the respective margin control is grounded. Current, -8 μA sink. Output Minimum Loading No minimum load Nominal Accuracy ±2 % max. of Vsetting Voltage Adjustment Range See Ordering Guide Temperature Coefficient ±40 ppm. per °C. of Vout Ripple/Noise See Ordering Guide Line/Load Regulation See Ordering Guide Efficiency See Ordering Guide Maximum Capacitive Loading Cap-ESR>=0.004 Ohms Cap-ESR <0.004 Ohms 8,250 μF non-ceramic (MPDTH03010 and MPDTH05010) 6,600 μF non-ceramic (MPDTH12010) Current Limit Inception 20 Amps Short Circuit Mode Protection Method Short Circuit Duration Autorecovery after overload removal Continuous, no damage (output shorted to ground) Sequencing Start-up of multiple units may be synchronized by connecting tracking pins. VoSense Input (Vout – VoSense) < 0.3 Volts Dynamic Characteristics Dynamic Load Response 70 μSec to within ±2% of final value (50 to 100% load step, 1A/ µSec load step, 330 μF external output cap) Switching Frequency 300 KHz (MPDTH03010 and MPDTH05010) 350 KHz (MPDTH12010) Environmental Calculated MTBF [4] 5.7 million hours,min. (MPDTH03010 and MPDTH03010) 6.4 million hours,min. (MPDTH12010) Operating Temperature Range -40 to +85 deg.C. (no condensation) Storage Temperature Range -40 to +125 deg.C. MPDTH**010 Series Performance and Functional Specifications All specifications are typical unless noted. Notes: All specifications are typical at nominal input line voltage, nominal output voltage and full load, Ta=+25 deg.C. unless otherwise noted. See detailed specifications. "TH" is a pinned through-hole package. "SM" is a surface mount package. Vin=3.3V, Vout=2.5V, Iout=10A Vin=5V, Vout=3.3V, Iout=10A Vin=12V, Vout=5V, Iout=10A Vin=3.3V, Vout=2.5V, Iout=15A Vin=5V, Vout=3.3V, Iout=15A Vin=12V, Vout=5V, Iout=15A The minimum input voltage is +2.95V. Or (Vout + 0.65V.), whichever is greater. RoHS6 compliance does not claim EU RoHS exemption 7b (lead in solder). Specification Notes: (1) All specifications are typical unless noted. General conditions for Specifications are +25 deg.C ambient, Vin=nominal, Vout=+2.5V, full load. Cin=470 mF (required for models MPDTH03010, 05010), Cout= 0 mF. For model MPDTH12010, the required input capacitor is 560 µF. See note 3. Adequate airflow must be supplied for extended testing under power (2) An external output capacitor is not required. However, a 330 μF output capacitor improves transient response. (3) The required input capacitor must have a ripple current rating of 700 mA RMS or greater for models MPDTH03010 and MPDTH05010. For model MPDTH12010, the ripple rating must be 800 mA RMS or greater. (4) Mean Time Before Failure is calculated using the Telcordia (Belcore) TR-332 50% stress, ground benign conditions, Tambient=+40 deg.C. (5) Track input is grounded or equal to Vin. (6) There is no input protection against overvoltage or reversed polarity. Please provide proper fusing and a back-biased diode if there is the possibility of improper polarity. Refer to the Con- nection Diagram. (7) The outputs are not intended to sink appreciable reverse current. (8) Output current limit and short circuit protection is non-latching. When the overcurrent fault is removed, the converter will immediately recover. (9) Connect VoSense to Vout remotely at the load for optimal accuracy. If not used at the load, connect VoSense to Vout at the converter. Do not exceed 0.3 Volts difference between Vout and VoSense. |
Similar Part No. - MPDTH05010WAS |
|
Similar Description - MPDTH05010WAS |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |