Model Selection Guide

Mechanical Dimensions

Notes:

Pin

Single

Dual

Triple

1

AC-Ground AC-Ground AC-Ground

2

AC-Neutral AC-Neutral AC-Neutral

3

AC-Line

AC-Line

AC-Line

4

-Vo 1

-Vo 2

-Vo 1

5

No Pin

No Pin

+Vo 1

6

No Pin

Common

-Vo 2

7

No Pin

No Pin

Common

8

+Vo 1

+Vo 1

+Vo 2

Pin Connections

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Notes:

1. Load regulation is measured for an output change of 10% to 90% at nominal input

line. For multiple output models, the loads are balanced.

2. The MPM-05 series is specified for operation over the wide operating temperature

range of -20°C to +55°C without derating. For operation over +55°C, derate the

power linearly by 3.75%/°C from +55°C to +70°C.

3. Single output models are approved to EN60950. Approval for other models is pending.

4. It is recommended that a fuse be used on the input of a power supply for protection.

For the MPM-05 series, a 1A/250 VAC slow blow should be used.

Model

Number

Input

Efficiency

(%, Typ)

Voltage

(VDC)

Over Volt.

Protection

(VDC)

Voltage

(VDC)

Over Volt.

Protection

(VDC)

Voltage

(VDC)

Typ.

Load

Reg.

Typ.

Load

Reg.

Typ.

Load

Reg.

MPM-05S-03

0.12

0.07

3.3

1.00

±1.0%

6.5

76

MPM-05S-05

0.12

0.07

5.0

1.00

±1.0%

6.5

76

MPM-05S-12

0.12

0.07

12.0

0.42

±1.0%

20.0

76

MPM-05S-15

0.12

0.07

15.0

0.33

±1.0%

20.0

76

MPM-05S-24

0.12

0.07

24.0

0.23

±1.0%

30.0

76

MPM-05D-05

0.12

0.07

+5.0

+0.50

±2.0%

6.5

-5.0

-0.50 ±2.0%

6.5

76

MPM-05D-12

0.12

0.07

+12.0

+0.21

±2.0%

20.0

-12.0

-0.21 ±2.0%

20.0

76

MPM-05D-15

0.12

0.07

+15.0

+0.16

±2.0%

20.0

-15.0

-0.16 ±2.0%

20.0

76

MPM-05T-0505

0.12

0.07

5.0

0.90

±3.0%

6.5

+5.0

+0.10 ±5.0%

-5.0 -0.10 ±5.0%

76

MPM-05T-0512

0.12

0.07

5.0

0.70

±3.0%

6.5

+12.0

+0.10 ±5.0%

-12.0 -0.10 ±5.0%

76

MPM-05T-0515

0.12

0.07

5.0

0.70

±3.0%

6.5

+15.0

+0.08 ±5.0%

-15.0 -0.08 ±5.0%

76

MPM-05T-0524

0.12

0.07

5.0

0.70

±3.0%

6.5

+24.0

+0.05 ±5.0%

-24.0 -0.05 ±5.0%

76

Typical Connection

Vout

C1, C3, C5

C2, C4, C6

Fuse

TVS

3.3

330 ~ 1,000

µF/16V

0.1

µF/50V

Ceramic

1A/

250 VAC

Slow Blow

P6KE6.8A

5.0

330 ~ 1,000

µF/16V

P6KE6.8A

12.0

220

µF/25V

P6KE16A

15.0

220

µF/25V

P6KE20A

24.0

120

µF/35V

P6KE33A

Typical Component Values

Notes:

1. C1, C3 and C5 are high frequency, low resistance electrolytic capacitors.

Refer to the suppliers specifications for capacitance/current ratings.

2. Voltage derating on all capacitors should be

80% or higher.

3. C2, C4 and C6 eliminate high frequency noise.

4. The TVS is recommended to protect load

circuitry in the event of a module failure.