Electronic Components Datasheet Search |
|
LT3070EUFDTRPBF Datasheet(PDF) 8 Page - Linear Technology |
|
LT3070EUFDTRPBF Datasheet(HTML) 8 Page - Linear Technology |
8 / 24 page LT3070 8 3070p PIN FUNCTIONS VIOC (Pin 1): Voltage for In-to-Out Control. The IC in- corporates a unique tracking function to control a buck regulator powering the LT3070’s input. The VIOC pin is the output of this tracking function that drives the buck regulator to maintain the LT3070’s input voltage at VOUT + 300mV. This function maximizes efficiency and minimizes power dissipation. See the Applications Information sec- tion for more information on proper control of the buck regulator. PWRGD (Pin 2): Power Good. The PWRGD pin is an open- drain NMOS output that is active low if any one of these fault modes is detected: • VOUT is less than 90% of VOUT(NOMINAL) on the rising edge of VOUT • VOUT drops below 85% of VOUT(NOMINAL) for more than 25μs • Junction temperature exceeds 145°C See the Applications Information section for more infor- mation on PWRGD fault modes. REF/BYP (Pin 3): Reference Filter. The pin is the output of the bandgap reference and has an impedance of ap- proximately 19kΩ. This pin must not be externally loaded. Bypassing the REF/BYP pin to GND with a 10nF capacitor decreases output voltage noise and provides a soft-start function to the reference. See the Applications Information section for more information on noise and output voltage margining considerations. GND (Pins 4, 9-14, 20, 26): Ground. All GND pins must be tied together and to Pin 29, the exposed backside of the package for proper thermal performance. These GND pins are fused to the internal die attach paddle and exposed package backside to optimize heat sinking and thermal resistance performance. IN (Pins 5, 6, 7, 8): Input Supply. These pins supply power to the high current pass transistor. Tie all IN pins together for proper performance. The LT3070 requires a bypass capacitor at IN to maintain stability and low input impedance over frequency. A 47μF input bypass capacitor suffices for most battery and power plane impedances. Minimizing input trace inductance optimizes performance. Applications that operate with low VIN-VOUT differential voltages and that have large, fast load transients may require much higher input capacitor requirements to prevent the input supply from drooping and allowing the regulator to enter dropout. See the Applications Information section for more information on input capacitor requirements. OUT (Pins 15, 16, 17, 18): Output. These pins supply power to the load. Tie all OUT pins together for proper performance. A minimum output capacitance of 15μF is required for stability. LTC recommends low ESR, X5R or X7R dielectric ceramic capacitors for best performance. A parallel ceramic capacitor combination of 10μF + 4.7μF + 2.2μF provides excellent stability and load transient response. Large load transient applications require larger output capacitors to limit peak voltage transients. See the Applications Information section for more information on output capacitor requirements. SENSE (Pin 19): Kelvin Sense for OUT. The SENSE pin is the inverting input to the error amplifier. Optimum regulation is obtained when the SENSE pin is connected to the OUT pins of the regulator. In critical applications, the resistance (RP)ofPCBtracesbetweentheregulatorandtheloadcause small voltage drops, creating a load regulation error at the point of load. Connecting the SENSE pin at the load instead of directly to OUT eliminates this voltage error. Figure 1 illustrates this Kelvin-Sense connection method. Note that the voltage drop across the external PCB traces adds to the dropout voltage of the regulator. The SENSE pin input bias current depends on the selected output voltage. SENSE pin input current varies from 50μA typically at VOUT = 0.8V to 300μA typically at VOUT = 1.8V. BIAS LT3070 IN EN VO2 VO1 VBIAS VIN VO0 MARGSEL MARGTOL VIOC SENSE OUT PWRGD RP REF/BYP GND + + RP 3070 F01 LOAD Figure 1. Kelvin Sense Connection |
Similar Part No. - LT3070EUFDTRPBF |
|
Similar Description - LT3070EUFDTRPBF |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |