Electronic Components Datasheet Search |
|
CS4362A-DQZR Datasheet(PDF) 7 Page - Cirrus Logic |
|
CS4362A-DQZR Datasheet(HTML) 7 Page - Cirrus Logic |
7 / 50 page DS617F2 7 CS4362A VQ 21 Quiescent Voltage (Output) - Filter connection for internal quiescent voltage. VQ must be capacitively coupled to analog ground, as shown in the Typical Connection Diagram. The nom- inal voltage level is specified in the Analog Characteristics and Specifications section. VQ pre- sents an appreciable source impedance and any current drawn from this pin will alter device performance. However, VQ can be used to bias the analog circuitry assuming there is no AC signal component and the DC current is less then the maximum specified in the Analog Charac- teristics and Specifications section. FILT+ 20 Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling cir- cuits. Requires the capacitive decoupling to analog ground as shown in the Typical Connection Diagram. AOUTA1 +,- AOUTB1 +,- AOUTA2 +,- AOUTB2 +,- AOUTA3 +,- AOUTB3 +,- 39,40 38,37 35,36 34,33 29,30 28,27 Differential Analog Output (Output) - The full-scale differential analog output level is specified in the Analog Characteristics specification table. MUTEC1 MUTEC2 MUTEC3 MUTEC4 MUTEC5 MUTEC6 41 26 25 24 23 22 Mute Control (Output) - These pins are intended to be used as a control for external mute cir- cuits on the line outputs to prevent the clicks and pops that can occur in any single supply sys- tem. Use of Mute Control is not mandatory but recommended for designs requiring the absolute minimum in extraneous clicks and pops. Hardware Mode Definitions M0 M2 M3 17 16 15 42 Mode Selection (Input) - Determines the operational mode of the device as detailed in Table 6 and Table 7. Software Mode Definitions SCL/CCLK 15 Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pull-up resistor to the logic interface voltage in I²C® Mode as shown in the Typical Connection Diagram. SDA/CDIN 16 Serial Control Port Data (Input/Output) - SDA is a data I/O line in I²C Mode and is open drain, requiring an external pull-up resistor to the logic interface voltage, as shown in the Typical Con- nection Diagram; CDIN is the input data line for the control port interface in SPI™ mode. AD0/CS 17 Address Bit 0 (C) / Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I²C Mode; CS is the chip select signal for SPI mode. DSD Definitions DSDA1 DSDB1 DSDA2 DSDB2 DSDA3 DSDB3 3 2 1 48 47 46 Direct Stream Digital Input (Input) - Input for Direct Stream Digital serial audio data. DSD_SCLK 42 DSD Serial Clock (Input) - Serial clock for the Direct Stream Digital serial audio interface. DSD_EN 7 DSD Enable (Input) - When held at logic ‘1’, the device will enter DSD Mode (Stand-Alone Mode only). Pin Name # Pin Description |
Similar Part No. - CS4362A-DQZR |
|
Similar Description - CS4362A-DQZR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |