Electronic Components Datasheet Search |
|
AS2702-16 Datasheet(PDF) 9 Page - ams AG |
|
AS2702-16 Datasheet(HTML) 9 Page - ams AG |
9 / 13 page AS2702 – AS-Interface Slave IC Revision 1.3, 21-Aug-08 Page 9 of 13 Symbol Parameter Min Max Unit Note VSCHLT Input threshold voltage 2.5 3.5 V 2 VIN Acceptable input voltage @ output off -0.3 40 V Notes: 1 The passive high-side current-source provides an about constant input current @ 0V <= VIN <= 4V 2 No hysteresis implemented Though equipped for bidirectional data transfer as D3, …, D0, the parameter port is nevertheless less flexible than the data port. Note the following differences: a) The parameter port is set portwise, the data port bitwise by the IO-configuration code; b) The parameter port can only be set to either ‘output’ or ‘input’. A bidirectional behaviour within a strobe cycle is not possible; c) The parameter port is set to ‘output’ as a rule; the only exception occurs in case of IO-configuration 7 and a master data request, which set it to ‘input’. To govern the data transfer at the parameter port P3, …, P0 strobe pin PSTBn is equipped with a low-side open-drain output switch plus a passive high-side current source with a nom. 10µA pull-up current capability. Typically the PSTBn-strobe width is about 6µs see Figure 4. (However to simplify and shorten the component test time of the slave device, the PSTBn pin is also used as an input. Input low pulses of more than 50µs each will step and cycle the device through 3 different test modes beyond the regular operation as described in this datasheet.) The dc- and timing parameters of strobe pin PSTBn are specified as follows: Symbol Parameter Min Max Unit Note IOUTLO Sink current @ output L 10 mA VOUT = 1V IOUTHI Leakage current @ output off -10 10 µA VOUT = 5V IINLO Input current @ VIN = 1V -5 -20 µA 1 VSCHLT Input threshold voltage 1.5 3.5 V 2 VIN Acceptable input voltage @ output off -0.3 40 V tNOTM PSTBn L-phase width, not triggering test mode 35 µs tTM PSTBn L-phase width, triggering test mode 50 µs CPINEXT Stray capacitance 20 pF Notes: 1 PSTBn is equipped with an on-chip pull-up current source, which ensures a sufficiently fast LH-edge upon output switch-off in open-pin condition, to prevent erroneous test mode triggering. If PSTBn has an external load connected to it, an additional external pull-up resistor may be needed to prevent erroneous test mode triggering upon output switch-off 2 No hysteresis implemented |
Similar Part No. - AS2702-16 |
|
Similar Description - AS2702-16 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |