Electronic Components Datasheet Search |
|
G3PE-225BL Datasheet(PDF) 7 Page - Omron Electronics LLC |
|
G3PE-225BL Datasheet(HTML) 7 Page - Omron Electronics LLC |
7 / 12 page Single-phase Solid State Relays for Heaters G3PE 433 The SSR in operation may cause an unexpected accident. Therefore it is necessary to test the SSR under the variety of conditions that are possible. As for the characteristics of the SSR, it is necessary to consider differences in characteristics between individual SSRs. The ratings in this catalog are tested values in a temperature range between 15 °C and 30°C, a relative humidity range between 25% and 85%, and an atmospheric pressure range between 86 and 106 kPa. It will be necessary to provide the above conditions as well as the load conditions if the user wants to confirm the ratings of specific SSRs. Causes of Failure • Do not drop the G3PE or subject it to abnormal vibration or shock during transportation or mounting. Doing so may result in deterioration of performance, malfunction, or failure. • Tighten each terminal to the torque specified below. Improper tightening may result in abnormal heat generation at the terminal, which may cause burning. • Do not supply overvoltage to the input circuits or output circuits. Doing so may result in failure or burning. • Do not use or store the G3PE in the following conditions. Doing so may result in deterioration of performance. • Locations subject to static electricity or noise • Locations subject to strong electric or magnetic fields • Locations subject to radioactivity Mounting • The G3PE is heavy. Firmly mount the DIN Track and secure both ends with End Plates for DIN Track mounting models. When mounting the G3PE directly to a panel, firmly secure it to the panel. Screw diameter: M4 Tightening torque: 0.98 to 1.47 N·m Note: Make sure that the load current is 50% of the rated load current when the G3PE is mounted horizontally. For details on close mounting, refer to the related information under performance characteristics. Mount the G3PE in a direction so that the markings read natu- rally. Wiring • When using crimp terminals, refer to the terminal clearances shown below. • Make sure that all lead wires are thick enough for the current. • For three-element and two-element models, the output terminal will be charged even when the Relay is OFF. Touching the terminal may result in electric shock. To isolate the Relay from the power supply, install an appropriate circuit breaker between the power supply and the Relay. Always turn OFF the power supply before wiring the Unit. • Terminal L2 and terminal T2 of a 2-element model are internally connected to each other. Connect terminal L2 to the ground terminal of the power supply. If terminal L2 is connected to a terminal other than the ground terminal, cover all the charged terminals, such as heater terminals, to prevent electric shock and ground faults. Fuses • Use a quick-burning fuse on the output terminals to prevent accidents due to short-circuiting. Use a fuse with equal or greater performance than those given in the following table. Recommended Fuse Capacity Precautions for Correct Use Terminals Screw terminal diameter Tightening torque Input terminals M3.5 0.59 to 1.18 N·m Output terminals M4 0.98 to 1.47 N·m M5 1.57 to 2.45 N·m Panel Vertical Direction Mounted on a vertical surface Panel Mounted on a horizontal surface Rated G3PE output current Applicable SSR Fuse (IEC 60269-4) 15 A G3PE @15B Series 32 A 25 A G3PE @25B Series 35 A G3PE @35B Series 63 A 45 A G3PE @45B Series 7 mm 13 mm 10 mm 13 mm 12 mm M4 (15 A, 25 A) M5 (35 A, 45 A) 12.9 mm 12.4 mm 10 mm 7.0 mm M3.5 15-A and 25-A Models 35-A and 45-A Models M5 (35 A, 45 A) M4 (15 A, 25 A) Output Terminal Section for Three-phase Models Output Terminal Section for Single-phase Models Input Terminal Section |
Similar Part No. - G3PE-225BL |
|
Similar Description - G3PE-225BL |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |