Electronic Components Datasheet Search |
|
BU52004GUL Datasheet(PDF) 10 Page - Rohm |
|
BU52004GUL Datasheet(HTML) 10 Page - Rohm |
10 / 12 page BU52004GUL, BU52014HFV Technical Note 10/11 www.rohm.com 2010.01 - Rev.D © 2010 ROHM Co., Ltd. All rights reserved. ● Operation Notes 1) Absolute maximum ratings Exceeding the absolute maximum ratings for supply voltage, operating conditions, etc. may result in damage to or destruction of the IC. Because the source (short mode or open mode) cannot be identified if the device is damaged in this way, it is important to take physical safety measures such as fusing when implementing any special mode that operates in excess of absolute rating limits. 2) GND voltage Make sure that the GND terminal potential is maintained at the minimum in any operating state, and is always kept lower than the potential of all other pins. 3) Thermal design Use a thermal design that allows for sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 4) Pin shorts and mounting errors Use caution when positioning the IC for mounting on printed circuit boards. Mounting errors, such as improper positioning or orientation, may damage or destroy the device. The IC may also be damaged or destroyed if output pins are shorted together, or if shorts occur between the output pin and supply pin or GND. 5) Positioning components in proximity to the Hall IC and magnet Positioning magnetic components in close proximity to the Hall IC or magnet may alter the magnetic field, and therefore the magnetic detection operation. Thus, placing magnetic components near the Hall IC and magnet should be avoided in the design if possible. However, where there is no alternative to employing such a design, be sure to thoroughly test and evaluate performance with the magnetic component(s) in place to verify normal operation before implementing the design. 6) Slide-by position sensing Fig.29 depicts the slide-by configuration employed for position sensing. Note that when the gap (d) between the magnet and the Hall IC is narrowed, the reverse magnetic field generated by the magnet can cause the IC to malfunction. As seen in Fig.30, the magnetic field runs in opposite directions at Point A and Point B. Since the dual output Omnipolar detection Hall IC can detect the S-pole at Point A and the N-pole at Point B, it can wind up switching output ON as the magnet slides by in the process of position detection. Fig. 31 plots magnetic flux density during the magnet slide-by. Although a reverse magnetic field was generated in the process, the magnetic flux density decreased compared with the center of the magnet. This demonstrates that slightly widening the gap (d) between the magnet and Hall IC reduces the reverse magnetic field and prevents malfunctions. 7) Operation in strong electromagnetic fields Exercise extreme caution about using the device in the presence of a strong electromagnetic field, as such use may cause the IC to malfunction. 8) Common impedance Make sure that the power supply and GND wiring limits common impedance to the extent possible by, for example, employing short, thick supply and ground lines. Also, take measures to minimize ripple such as using an inductor or capacitor. 9) GND wiring pattern When both a small-signal GND and high-current GND are provided, single-point grounding at the reference point of the set PCB is recommended, in order to separate the small-signal and high-current patterns, and to ensure that voltage changes due to the wiring resistance and high current do not cause any voltage fluctuation in the small-signal GND. In the same way, care must also be taken to avoid wiring pattern fluctuations in the GND wiring pattern of external components. 10) Exposure to strong light Exposure to halogen lamps, UV and other strong light sources may cause the IC to malfunction. If the IC is subject to such exposure, provide a shield or take other measures to protect it from the light. In testing, exposure to white LED and fluorescent light sources was shown to have no significant effect on the IC. 11) Power source design Since the IC performs intermittent operation, it has peak current when it’s ON. Please taking that into account and under examine adequate evaluations when designing the power source. L Fig.29 d Magnet Hall IC Slide -10 -8 -6 -4 -2 0 2 4 6 8 10 0 123 456 789 10 Horizontal distance from the magnet [mm] Reverse Fig.31 Fig.30 B S A N Flux Flux |
Similar Part No. - BU52004GUL_10 |
|
Similar Description - BU52004GUL_10 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |