Design, Specifications are subject to change without notice.

Ask factory for technical specifications before purchase and/or use.

Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail.

Plastic Film Capacitors

Stacked Metallized PPS Film Chip Capacitor

Type:

ECHU(X)

Stacked metallized PPS film as dielectric with simple

mold-less construction

IFeatures

IRecommended Applications

IExplanation of Part Numbers

123456789

10

11

12

E

C

H

U

Product code

Dielectric &

construction

Rated voltage

Capacitance

X

Cap. Tol. Suffix

Suffix

G ±2 %

J

±5 %

ISpecifications

IConstruction

IDimensions in mm (not to scale)

❈ Please consult us for flow soldering

❈ In case of applying voltage in alternating current (50 Hz or 60 Hz sine wave) to a capacitor with DC rated voltage, please

refer to the page of “Permissible voltage (R.M.S) in alternating current corresponding to DC rated voltage”.

01

10 VDC

1C 16 VDC

1H 50 VDC

5

8 mm

size ø180 mm

9

12 mm

size ø330 mm

and diameter

ø330 mm reel is

prepared.

Tape width

Reel diameter

Category temp. range

(Including temperature-rise on unit surface)

Rated voltage

Capacitance range

Capacitance tolerance

Withstand voltage

Dissipation factor (tan )

Insulation resistance (IR)

−55 ℃ to ＋125 ℃

10 VDC

，16 VDC，50 VDC

(50 VDC: 0.12 µF or more: Derating or rated voltage by 1.25 % /

℃at more than 105 ℃)

0.00010 µF to 0.22 µF (E12)

±2 %(G), ±5 %(J)

tan

δ≦0.6 % (20 ℃, 1 kHz)

10 VDC

：IR≧3000 MΩ (20 ℃, 10 VDC, 60 s)

16 VDC

：IR≧3000 MΩ (20 ℃, 10 VDC, 60 s)

50 VDC

：IR≧3000 MΩ (20 ℃, 50 VDC, 60 s)

Soldering conditions

Reflow soldering : 260 ˚C max. and 95 sec max. at more than 220 ˚C (Temp. at cap. surface)

saize

code

L

WH

e

g

K1

1.6

0.8

0.7

0.35

≧0.4

J1

2.0

1.25

0.9

0.45

≧0.6

J2

2.0

1.25

1.1

0.45

≧0.6

H1

3.2

1.6

0.9

0.65

≧1.0

H2

3.2

1.6

1.1

0.65

≧1.0

H3

3.2

1.6

1.5

0.65

≧1.0

G1

3.2

2.5

1.1

0.65

≧1.0

G2

3.2

2.5

1.5

0.65

≧1.0

G3

3.2

2.5

2.1

0.65

≧1.0

E1

4.8

3.3

1.5

0.80

≧2.0

E2

4.8

3.3

2.1

0.80

≧2.0

D1

6.0

4.1

1.9

0.80

≧2.0

D3

6.0

4.1

2.5

0.80

≧2.0

D4

6.0

4.1

2.8

0.80

≧2.0