2

MODEL

OUTPUT

ADJUSTMENT

OUTPUT

PEAK CURRENT

LINE

LOAD

TYPICAL RIPPLE &

INITIAL SETTING

VOLTAGE

RANGE

CURRENT

(NOTE 1)

REGULATION

REGULATION

NOISE %p-p (NOTE 2)

ACCURACY

+5V

4.75V to 5.50V

20A

30A

1%

1%

1%

5.1V to 5.2V

MAP130-4003

+15V

14.0V to 16.0V

4A

8A

1%

2%

1%

15.0V to 15.1V

-5V

Fixed

1A

1A

2%

2%

1%

4.9V to 5.1V

-15V

Fixed

1A

1A

2%

2%

1%

14.7V to 15.3V

+5V

4.75V to 5.50V

20A

30A

0.2%

1%

1%

5.15V to 5.2V

MAP130-4004

+24V

23.0V to 25.0V

3.5A

5A

0.5%

2%

1%

23.9V to 24.1V

-15V

Fixed

1A

1A

0.5%

2%

1%

-14.5V to -15.5V

+15V

Fixed

1A

1A

0.5%

2%

1%

14.5V to 15.5V

+5V

4.75V to 5.50V

20A

30A

0.2%

1%

1%

5.1V to 5.25V

MAP130-4010

+12V

11.5V to 12.8V

5A

10A

0.5%

2%

1%

11.75V to 12.0V

-5V

Fixed

1A

1A

0.5%

2%

1%

-4.8V to -5.2V

-12V

Fixed

3A

3A

0.5%

2%

1%

-11.6V to -12.4V

+5V

4.75V to 5.50V

20A

30A

0.2%

1%

1%

5.1V to 5.25V

MAP130-4020

+12V

11.5V to 12.8V

5A

10A

0.5%

2%

1%

11.75V to 12.0V

-12V

Fixed

1A

1A

0.5%

2%

1%

-11.6V to -12.4V

-5V

Fixed

3A

3A

0.5%

2%

1%

-4.8V to -5.2V

NOTES: 1) Peak loads up to 165 Watts, (total of all outputs), for 60 seconds or less are acceptable, (10% duty cycle max.).

2) Maximum peak to peak noise expressed as a percentage of output voltage, 20MHz bandwidth.

INPUT SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Input Voltage- AC

Auto-ranging.

Low Range

90

115

132

VAC

High Range

175

230

264

Input Frequency

AC Input.

47

63

Hz

Brown out Protection

Lowest AC input voltage that regulation is maintained with full rated loads.

90

VAC

Hold-up Time

Nominal AC input voltage (115 VAC).

130W load:

40

mS

Input Current

90 VAC, 130W load.

3.3

Input Protection

Non-user serviceable internally located AC input line fuse.

Inrush Surge Current

Internally limited by thermistor. Vin = 264 VAC (one cycle). 25° C.

38

Operating Frequency

Switching frequency of main transformer (variable).

Range:

16

120

kHz

OUTPUT SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Efficiency

Full Load, 115VAC. Varies with distribution of loads among outputs.

71

80

%

Minimum Loads

MAP130-1012.

1.25

MAP130-1024.

0.63

Amps

MAP130-1005 and all multiple output models, main channel only.

3.00

Ripple and Noise

Full load, 20MHz bandwidth.

See Model Selection Chart

Output Power

Continuous output power, all multiple output models.

130

Watts

Peak output power (60s maximum, 10% duty cycle), all multiple output models.

165

Overshoot /Undershoot

Output voltage overshoot/undershoot at turn-on / turn-off

1

%

Regulation

Varies by output, Total regulation includes: line changes from 90-132 VAC

See Model Selection Chart

or 175-264, changes in load starting at 20% load and changing to 100% load.

Transient Response

Recovery time to within 1% of initial set point due to a 50-100% load change,

500

µS

4% max. deviation. (Main output only on multi-output units)

Turn-on Delay

Time required for initial output voltage stabilization.

2

Sec

Turn-on Rise Time

Time required for output voltage to rise from 10% to 90%.

20

mS

MAP130 SERIES