E5AN-H/E5EN-H

8

Characteristics

*1. The indication accuracy of K thermocouples in the −200 to 1300°C range, T and N thermocouples at a temperature of −100°C max., and U

and L thermocouples at any temperatures is

±2°C ±1 digit max. The indication accuracy of the B thermocouple at a temperature of 400°C max.

is not specified. The indication accuracy of B thermocouples in the 400 to 800

°C range is ±3°C max. The indication accuracy of the R and S

thermocouples at a temperature of 200

°C max. is ±3°C ±1 digit max. The indication accuracy of W thermocouples is ±0.3% of PV or ±3°C,

whichever is greater,

±1 digit max.

The indication accuracy of PL II thermocouples is

±0.3% of PV or ±2°C, whichever is greater, ±1 digit max.

*2. Ambient temperature: −10°C to 23°C to 55°C, Voltage range: −15% to 10% of rated voltage

*3. K thermocouple at −100°C max.: ±10°C max.

*4. External communications (RS-232C, RS-485, or RS-422) and cable communications for the Setup Tool can be used at the same time.

*5. Refer to information on maritime standards in Safety Precautions for E5

Indication accuracy

Thermocouple: (

±0.1% of indicated value or ±1°C, whichever is greater) ±1 digit max. *1

Platinum resistance thermometer: (

±0.1% of indicated value or ±0.5°C, whichever is greater) ±1 digit max.

Analog input:

±0.1% FS ±1 digit max.

CT input:

±5% FS ±1 digit max.

Potentiometer input: ±5% FS ±1 digit max.

Transfer output accuracy

±0.3% FS max.

Influence of temperature

*2

Thermocouple input (R, S, B, W, PL II): (

±1% of PV or ±10°C, whichever is greater) ±1 digit max.

Other thermocouple input: (

±1% of PV or ±4°C, whichever is greater) ±1 digit max. *3

Platinum resistance thermometer: (

±1% of PV or ±2°C, whichever is greater) ±1 digit max.

Analog input: (

±1%FS) ±1 digit max.

Influence of voltage

*2

Input sampling period

60 ms

Hysteresis

Temperature input: 0.1 to 3240.0

°C or °F (in units of 0.1°C or °F)

Analog input: 0.01% to 99.99% FS (in units of 0.01% FS)

Proportional band (P)

Temperature input: 0.1 to 3240.0

°C or °F (in units of 0.1°C or °F)

Analog input: 0.1% to 999.9% FS (in units of 0.1% FS)

Integral time (I)

0.0 to 3240.0 s (in units of 0.1 s)

Derivative time (D)

0.0 to 3240.0 s (in units of 0.1 s)

Control period

0.5, 1 to 99 s (in units of 1 s)

Manual reset value

0.0 to 100.0% (in units of 0.1%)

Alarm setting range

−19999 to 32400 (decimal point position depends on input type)

Affect of signal source

resistance

Thermocouple: 0.1

°C/Ω max. (100 Ω max.)

Platinum resistance thermometer: 0.1

°C/Ω max. (10 Ω max.)

Insulation resistance

20 M

Ω min. (at 500 VDC)

Dielectric strength

2,300 VAC, 50 or 60 Hz for 1 min (between terminals with different charge)

Vibration

resistance

Destruction 10 to 55 Hz, 0.75-mm single amplitude for 2 hrs each in X, Y, and Z directions

Shock

resistance

Weight

E5AN-H

Controller: Approx. 310 g, Mounting Bracket: Approx. 100 g

E5EN-H

Controller: Approx. 260 g, Mounting Bracket: Approx. 100 g

Degree of protection

Front panel: IP66, Rear case: IP20, Terminals: IP00

Memory protection

Non-volatile memory (number of writes: 1,000,000 times)

Setup Tool

CX-Thermo version 4.0 or higher

Setup Tool port

Provided on the bottom of the E5AN-H and E5EN-H.

An E58-CIFQ1 USB-Serial Conversion Cable is required to connect the computer to the E5AN-H and E5EN-H.

Provided on the front of the E5AN-H and E5EN-H. An E58-CIFIR USB-infrared Conversion Cable is required to

connect the computer to the E5AN-H or E5EN-H.

*4

Standards

Approved

standards

UL 61010-1, CSA C22.2 No. 1010-1

Conformed

standards

EN 61010-1 (IEC 61010-1): Pollution level 2, overcurrent category II, Lloyd's standards

*5

EMC

EMI:

EN 61326

Radiated Interference Electromagnetic Field Strength: EN 55011 Group 1, class A

Noise Terminal Voltage:

EN 55011 Group 1, class A

EMS:

EN 61326

ESD Immunity:

EN 61000-4-2

Electromagnetic Field Immunity:

EN 61000-4-3

Burst Noise Immunity:

EN 61000-4-4

Conducted Disturbance Immunity:

EN 61000-4-6

Surge Immunity:

EN 61000-4-5

Power Frequency Magnetic Field Immunity:

EN 61000-4-8

Voltage Dip/Interrupting Immunity:

EN 61000-4-11