Electronic Components Datasheet Search |
|
MHV2805S Datasheet(PDF) 10 Page - Interpoint Corporation Company |
|
MHV2805S Datasheet(HTML) 10 Page - Interpoint Corporation Company |
10 / 19 page TRIPLE OUTPUT MODEL – MHV28512T 5 (MAIN) ±12 (AUXILIARIES) units parameter ConDitions MIN TyP MAX MIN TyP MAX output voltage MAIN AND POS. AUX 4.90 5.00 5.10 11.76 12.00 12.24 VDC NEG. AUX. -11.70 -12.00 -12.30 output Current 2 0 — 2.0 0 ±0.208 0.333 1 A TOTAL — — — — — 0.416 output poWer 3 0 — 10 0 ±2.50 4.00 1 W vin = 16 to 50 vDC TOTAL — — — — — 5 output ripple 10 khz - 2 mhz — 8 22 — 9 22 mV p-p line regulation MAIN AND POS. AUX — 0 5 — 5 35 mV vin= 16 to 50 vDC NEG. AUX. — 7 40 loaD regulation 4 MAIN AND POS. AUX — 10 20 — 10 30 NEG. AUX. — — — — 40 70 mV Cross regulation 5 EFFECT ON NEGATIVE AUXILIARy — — — — 400 800 mV input voltage Continuous 16 28 50 — — — VDC transient 120 ms 1 — — 80 — — — V input Current no loaD — 30 37 — — — mA inhibiteD — 8.4 10 — — — input ripple Current 10 kHz - 10 MHz — 10 30 — — — mA p-p eFFiCienCy 74 78 — — — — % loaD Fault 6 POWER DISSIPATION — — 9.5 — — 9.5 W reCovery 1 — — 25 — — 25 ms step loaD response 7 transient — — ±350 — — ±600 mV pk NEG. AUX. 1 — — — — — ±600 reCovery — — 3 — — 4 ms NEG. AUX. 1 — — — — — 4 step line response 1, 8 16 - 50 - 16 vin transient — — ±400 — — ±500 mV pk reCovery — — 3 — — 4 ms start-up Delay — 7 15 — 7 15 ms overshoot 1 — — 100 — — 240 mV pk CapaCitive loaD 1 25°C — — 200 — — 100 µF Notes for Triple Output Models 1. guaranteed by design, not tested. 2. The sum of the 12 volt auxiliary output currents may not exceed 416 mA. 3. The sum of the auxiliary output power may not exceed 5 watts. Up to 80% of the total power (5W) is available from either auxiliary providing the opposite auxiliary is carrying 20% of the total auxiliary power used. 4. Load regulation for the +5 is specified at 0.0 to 2.0 A with the aux. both held at 2.5 W (208 mA). Load regulation for the auxiliary. is specified as both auxiliaries from 0.0 to 2.5 W (208 mA) at the same time with the +5 held at 2.0 A. 5. Cross regulation occurs between the two auxiliaries and is measured on –aux. +5 is held constant at 2.0 A. Cross regulation is specified for two conditions: A. Positive aux. = 2.5 W (50%); negative aux. = 2.5 W to 0.5 W (50% to 10%). B. From +Po = 70% and -Po = 30% to + Po = 30% and -Po =70%. Above conditions are referenced to 50%/50% balanced loads. 6.Loadfaultisashortcircuit(<50mΩ).Recoveryisintoaresistiveload. 7.Steploadtransition≥10µs.Recovery=timetosettletowithin1%ofVOUT final value. 8.Steplinetransition≥10µs.Recovery=timetosettletowithin1%ofVOUT final value. Electrical Characteristics: -55° to +125°C TC, 28 VDC Vin, 100% load, free run, unless otherwise specified. Crane Aerospace & Electronics Power Solutions MHV single, dual and triple dc/dc converters 28 Volt input – 15 Watt www.interpoint.com Page 10 of 19 MHV Rev E - 20100503 |
Similar Part No. - MHV2805S |
|
Similar Description - MHV2805S |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |