SE98ATL datasheet(5/43 Pages) NXP

Part #	SE98ATL

Description	DDR memory module temp sensor, 1.7 V to 3.6 V

Download	43 Pages

Scroll/Zoom	100%

Manufacturer	NXP [NXP Semiconductors]

Direct Link	http://www.nxp.com

Logo

5 / 43 page

SE98A_4

Product data sheet

Rev. 04 — 25 November 2009

5 of 43

NXP Semiconductors

SE98A

DDR memory module temp sensor, 1.7 V to 3.6 V

7.

Functional description

7.1 Serial bus interface

The SE98A uses the 2-wire serial bus (I2C-bus/SMBus) to communicate with a host

controller. The serial bus consists of a clock (SCL) and data (SDA) signals. The device

can operate on either the I2C-bus Standard/Fast mode or SMBus. The I2C-bus

Standard-mode is defined to have bus speeds from 0 Hz to 100 kHz, I2C-bus Fast-mode

from 0 Hz to 400 kHz, and the SMBus is from 10 kHz to 100 kHz. The host or bus master

generates the SCL signal, and the SE98A uses the SCL signal to receive or send data on

the SDA line. Data transfer is serial, bidirectional, and is one bit at a time with the Most

Significant Bit (MSB) transferred first, and a complete I2C-bus data is 1 byte. Since SCL

and SDA are open-drain, pull-up resistors must be installed on these pins.

7.2 Slave address

The SE98A uses a 4-bit fixed and 3-bit programmable (A0, A1 and A2) 7-bit slave address

that allows a total of eight devices to coexist on the same bus. The input of each pin is

sampled at the start of each I2C-bus/SMBus access. The A0, A1 and A2 pins are pulled

LOW internally. The A0 pin is also overvoltage tolerant, supporting 10 V software write

protection when applied to the SPD that shares common address lines.

Fig 5.

Slave address

R/W

002aab304

0

1

A2

A1

A0

fixed

hardware

selectable

slave address

MSB

LSB

X

Similar Part No. - SE98ATL

Manufacturer	Part #	Datasheet	Description
NXP Semiconductors	SE98ATL	227Kb / 43P	DDR memory module temp sensor, 1.7 V to 3.6 V Rev. 02-6 August 2009

More results

Similar Description - SE98ATL

Manufacturer	Part #	Datasheet	Description
NXP Semiconductors	SE98A	227Kb / 43P	DDR memory module temp sensor, 1.7 V to 3.6 V Rev. 02-6 August 2009
	SE98	193Kb / 39P	DDR memory module temp sensor, 3.3 V Rev. 04-2 February 2009
	SE97	427Kb / 55P	DDR memory module temp sensor with integrated SPD, 3.3 V Rev. 07-29 January 2010
	SE97	275Kb / 53P	DDR memory module temp sensor with integrated SPD, 3.3 V Rev. 06-17 August 2009
	SE97	281Kb / 54P	DDR memory module temp sensor with integrated SPD, 3.3 V Rev. 05-6 August 2009
	SE97B	401Kb / 53P	DDR memory module temp sensor with integrated SPD Rev. 01-27 January 2010
Skyworks Solutions Inc.	SKY66108	1Mb / 13P	2.0 V to 3.6 V supply operation
NXP Semiconductors	K60P120M100SF2	2Mb / 72P	Voltage range: 1.71 to 3.6 V Rev. 7, 02/2013
	K60P100M100SF2	2Mb / 76P	Voltage range: 1.71 to 3.6 V Rev. 7, 02/2013
	K60P100M100SF2V2	1Mb / 80P	Voltage range: 1.71 to 3.6 V Rev. 3, 6/2013

More results

SE98ATL Datasheet(PDF) 5 Page - NXP Semiconductors

SE98ATL Datasheet(HTML) 5 Page - NXP Semiconductors

Similar Part No. - SE98ATL

Similar Description - SE98ATL

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

Datasheet Download

Link URL