Electronic Components Datasheet Search |
|
LPC2378 Datasheet(PDF) 2 Page - NXP Semiconductors |
|
LPC2378 Datasheet(HTML) 2 Page - NXP Semiconductors |
2 / 68 page LPC2377_78 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 5 — 17 June 2010 2 of 68 NXP Semiconductors LPC2377/78 Single-chip 16-bit/32-bit microcontrollers General Purpose DMA controller (GPDMA) on AHB that can be used with the SSP serial interfaces, the I2S port, and the Secure Digital/MultiMediaCard (SD/MMC) card port, as well as for memory-to-memory transfers. Serial Interfaces: Ethernet MAC with associated DMA controller. These functions reside on an independent AHB. USB 2.0 full-speed device with on-chip PHY and associated DMA controller (LPC2378 only). Four UARTs with fractional baud rate generation, one with modem control I/O, one with IrDA support, all with FIFO. CAN controller with two channels (LPC2378 only). SPI controller. Two SSP controllers with FIFO and multi-protocol capabilities. One is an alternate for the SPI port, sharing its interrupt and pins. These can be used with the GPDMA controller. Three I2C-bus interfaces (one with open-drain and two with standard port pins). I2S (Inter-IC Sound) interface for digital audio input or output. It can be used with the GPDMA. Other peripherals: SD/MMC memory card interface. 104 General purpose I/O pins with configurable pull-up/down resistors. 10-bit ADC with input multiplexing among 8 pins. 10-bit DAC. Four general purpose timers/counters with 8 capture inputs and 10 compare outputs. Each timer block has an external count input. One PWM/timer block with support for three-phase motor control. The PWM has two external count inputs. Real-Time Clock (RTC) with separate power pin, clock source can be the RTC oscillator or the APB clock. 2 kB SRAM powered from the RTC power pin, allowing data to be stored when the rest of the chip is powered off. WatchDog Timer (WDT). The WDT can be clocked from the internal RC oscillator, the RTC oscillator, or the APB clock. Standard ARM test/debug interface for compatibility with existing tools. Emulation trace module supports real-time trace. Single 3.3 V power supply (3.0 V to 3.6 V). Four reduced power modes: idle, sleep, power-down, and deep power-down. Four external interrupt inputs configurable as edge/level sensitive. All pins on Port 0 and Port 2 can be used as edge sensitive interrupt sources. Processor wake-up from Power-down mode via any interrupt able to operate during Power-down mode (includes external interrupts, RTC interrupt, USB activity, Ethernet wake-up interrupt). Two independent power domains allow fine tuning of power consumption based on needed features. Each peripheral has its own clock divider for further power saving. Brownout detect with separate thresholds for interrupt and forced reset. On-chip power-on reset. |
Similar Part No. - LPC2378 |
|
Similar Description - LPC2378 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |