Electronic Components Datasheet Search |
|
MAX16070 Datasheet(PDF) 2 Page - Maxim Integrated Products |
|
MAX16070 Datasheet(HTML) 2 Page - Maxim Integrated Products |
2 / 52 page 12-Channel/8-Channel, Flash-Configurable System Managers with Nonvolatile Fault Registers 2 ______________________________________________________________________________________ Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. VCC, CSP, CSM to GND........................................-0.3V to +15V CSP to CSM..........................................................-0.7V to +0.7V MON_, GPIO_, SCL, SDA, A0, RESET to GND (programmed as open-drain outputs).................-0.3V to +6V EN, TCK, TMS, TDI to GND ....................................-0.3V to +4V DBP, ABP to GND...-0.3V to the lower of +3V and (VCC + 0.3V) TDO, GPIO_, RESET (programmed as push-pull outputs) .... -0.3V to (VDBP + 0.3V) Input/Output Current .........................................................20mA Continuous Power Dissipation (TA = +70NC) 40-Pin TQFN (derate 26.3mW/NC above +70NC).......2105mW Operating Temperature Range.......................... -40NC to +85NC Junction Temperature ....................................................+150NC Storage Temperature Range............................ -65NC to +150NC Lead Temperature (soldering, 10s) ................................+300NC Soldering Temperature (reflow) ......................................+260NC ELECTRICAL CHARACTERISTICS (VCC = 2.8V to 14V, TA = -40NC to +85NC, unless otherwise specified. Typical values are at VABP = VDBP = VCC = 3.3V, TA = +25NC.) (Note 1) ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Operating Voltage Range VCC Reset output asserted low 1.2 V (Note 2) 2.8 14 Undervoltage Lockout (Rising) VUVLO Minimum voltage on VCC to ensure the device is flash configurable 2.7 V Undervoltage Lockout Hysteresis VUVLO_HYS 100 mV Minimum Flash Operating Voltage Vflash Minimum voltage on VCC to ensure flash erase and write operations 2.7 V Supply Current ICC No load on output pins 4.5 7 mA During flash writing cycle 10 14 ABP Regulator Voltage VABP CABP = 1μF, no load, VCC = 5V 2.85 3 3.15 V DBP Regulator Voltage VDBP CDBP = 1μF, no load, VCC = 5V 2.8 3 3.1 V Boot Time tBOOT VCC > VUVLO 200 350 μs Flash Writing Time 8-byte word 122 ms Internal Timing Accuracy (Note 3) -8 +8 % EN Input Voltage VTH_EN_R EN voltage rising 1.41 V VTH_EN_F EN voltage falling 1.365 1.39 1.415 EN Input Current IEN -0.5 +0.5 μA Input Voltage Range 0 5.5 V |
Similar Part No. - MAX16070 |
|
Similar Description - MAX16070 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |