Electronic Components Datasheet Search |
|
SP9604JS Datasheet(PDF) 5 Page - Sipex Corporation |
|
SP9604JS Datasheet(HTML) 5 Page - Sipex Corporation |
5 / 11 page SP9604DS/03 SP9604 Quad, 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation 5 FEATURES The SP9604 is a low–power replacement for the popularSP9345,Quad12-BitDigital-to-AnalogCon- verter. ThisQuad,VoltageOutput,12-BitDigital-to- Analog Converter features ±4.5V output swings when using ±5voltsupplies.Theinputcodingformat usedisstandardoffsetbinary.(PleaserefertoTable1.) The converterutilizesdouble-bufferingoneachofthe 12 parallel digital inputs, for easy microprocessor interface. Each 12-bit DAC is independently addres- sable and all DACs may be simultaneously updated using a single XFER command. The output settling- time is specified at 30 µstofull12–bitaccuracywhen driving a 5Kohm, 50pf load combination. The SP9604,Quad12-BitDigital-to-AnalogConverteris ideally suited for applications such as ATE, process controllers,robotics,andinstrumentation. TheSP9604 is available in 28–pin plastic DIP or SOIC packages, specified over the commercial (0 °C to +70°C) temperature range. INPUT OUTPUT MSB LSB 1111 1111 1111 VREF - 1 LSB 1111 1111 1110 VREF - 2 LSB 1000 0000 0001 0 + 1 LSB 1000 0000 0000 0 0000 0000 0001 -VREF + 1 LSB 0000 0000 0000 -VREF 1 LSB = Table 1. Offset Binary Coding using the CS signal in both modes. The digital inputs are designed to be both TTL and 5V CMOS compat- ible. InordertoreducetheDACfullscaleoutputsensitivity to the large weighting of the MSB’s found in conven- tionalR-2Rresistorladders,the3MSB’saredecoded into 8 equally weighted levels. This reduces the contribution of each bit by a factor of 4, thus, reducing the output sensitivity to mis–matches in resistors and switches by the same amount. Linearity errors and stability are both improved for the same reasons. Each D/A converter is separated from the data bus by two registers, each consisting of level-triggered latches, Figure 1. The first register (input register) is 12-bits wide. The input register is selected by the address input A 0 and A1 and is enabled by the CS and WR1 signals. In the 8-bit mode, the enable signal to the 8 MSB’s is disabled by a logic low on B1/B2 to allow the 4 LSB’s to be updated. The second register (DACregister), acceptsthedecoded3MSB’splusthe 9 LSB’s. The four DAC registers are updated simul- taneously for all DAC’s using the XFER and WR2 signals. Using the CLR and WR2 signals or the power-on-reset,(enabledwhenthepowerisswitched on) the DAC registers are set to 1000 0000 0000 and the DAC outputs will settle to 0V. Usingthecontrollogicinputs,theuserhasfullcontrol of address decoding, chip enable, data transfer and clearing of the DAC’s. The control logic inputs are level triggered, and like the data inputs, are TTL and CMOS compatible. The truth table (Table 2) shows the appropriate functions associated with the states of the control logic inputs. The DACs themselves are implemented with a preci- sion thin–film resistor network and CMOS transmis- sion gate switches. Each D/A converter is used to convert the 12–bit input from its DAC register to a precision voltage. The bipolar voltage output of the SP9604 is created on-chip from the DAC Voltage Output (V DAC) by using an operational amplifier and two feedback resistors connected as shown in Figure 2. This configuration produces a ±4.5V bipolar output range with standard offset binary coding. THEORY OF OPERATION The SP9604 consists of five main functional blocks —inputdatamultiplexer,dataregisters,controllogic, four 12-bit D/A converters, and four bipolar output voltage amplifiers. The input data multiplexer is designed to interface to either 12- or 8-bit micropro- cessordatabusses. Theinputdataformatiscontrolled by the B1/B2 signal — a logic “1” selects the 12-bit mode, while a logic “0” selects the 8-bit mode. In the 12-bitmodethedataistransferredtotheinputregisters without changes in its format. In the 8-bit mode, the four least significant bits (LSBs) are connected to the four most significant bits (MSBs), allowing an 8-bit MSB-justified interface. All data inputs are enabled 2V REF 2 12 |
Similar Part No. - SP9604JS |
|
Similar Description - SP9604JS |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |