Electronic Components Datasheet Search |
|
TUSB1106IPWRQ1 Datasheet(PDF) 4 Page - Texas Instruments |
|
|
TUSB1106IPWRQ1 Datasheet(HTML) 4 Page - Texas Instruments |
4 / 24 page TUSB1106-Q1 SCAS916 – AUGUST 2011 www.ti.com FUNCTIONAL DESCRIPTION Function Selection FUNCTION TABLE SUSPND OE D+, D – RCV VP, VM FUNCTION L L Driving and receiving Active Active Normal driving (differential receiver active) L H Receiving(1) Active Active Receiving H L Driving Inactive(2) Active Driving during suspend(3) (differential receiver inactive) H H High-Z(1) Inactive(2) Active Low-power state (1) Signal levels on D+ and D – are determined by other USB devices and external pullup/pulldown resistors. (2) In suspend mode (SUSPND = HIGH) the differential receiver is inactive and output RCV is always LOW. Out of suspend (K), signaling is detected via the single-ended receivers VP and VM. (3) During suspend, the slew-rate control circuit of low-speed operation is disabled. The D+ and D – lines are still driven to their intended states, without slew-rate control. This is permitted because driving during suspend is used to signal remote wakeup by driving a K signal (one transition from idle to K state) for a period of 1 ms to 15 ms. Operating Functions Driving Function (Pin OE = L) Using Differential Input Data Interface DATA STATE VMO VPO DATA LOW SPEED FULL SPEED L L SE0 X X H L Differential logic 0 J K L H Differential logic 1 K J H H Illegal state X X Table 1. Receiving Function (Pin OE = H) DATA STATE D+, D – RCV VP(1) VM(1) LOW FULL SPEED SPEED Differential L L H J K logic 0 Differential H H L K J logic 1 SE0 RCV*(2) L L X X (1) VP = VM = H indicates the sharing mode (VCC(5.0) and Vreg(3.3) are disconnected). (2) RCV* denotes the signal level on output RCV just before SE0 state occurs. This level is stable during the SE0 period. Power-Supply Configurations The TUSB1106-Q1 can be used with different power-supply configurations, which can be dynamically changed. An overview is given in Table 3. • Normal mode – Both VCC(I/O) and VCC(5.0) or (VCC(5.0) and Vreg(3.3)) are connected. For 5-V operation, VCC(5.0) is connected to a 5-V source (4 V to 5.5 V). The internal voltage regulator then produces 3.3 V for the USB connections. For 3.3-V operation, both VCC(5.0) and Vreg(3.3) are connected to a 3.3-V source (3 V to 3.6 V). VCC(I/O) is independently connected to a voltage source (1.65 V to 3.6 V), depending on the supply voltage of the external circuit. • Disable mode – VCC(I/O) is not connected, VCC(5.0) or (VCC(5.0) and Vreg(3.3)) are connected. In this mode, the internal circuits of the TUSB1106-Q1 ensure that the D+ and D – pins are in 3-state and the power consumption drops to the low-power (suspended) state level. Some hysteresis is built into the detection of VCC(I/O) lost. • Sharing mode – VCC(I/O) is connected, (VCC(5.0) and Vreg(3.3)) are not connected. In this mode, the D+ and D– pins are made 3-state and the TUSB1106-Q1 allows external signals of up to 3.6 V to share the D+ and D – 4 Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): TUSB1106-Q1 |
Similar Part No. - TUSB1106IPWRQ1 |
|
Similar Description - TUSB1106IPWRQ1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |