The copyright and authority for the interpretation of the products are reserved by MORNSUN

Specifications subject to change without notice

LH05-25

A/3-2012

Page 6 of 8

LH15-10B48

33

SMBJ64A

LH15-10A05

470

470

SMBJ7.0A

SMBJ7.0A

LH15-10A12

220

220

SMBJ20A

SMBJ20A

LH15-10A15

120

120

SMBJ20A

SMBJ20A

LH15-10C0505-05

470

220

220

SMBJ7.0A

SMBJ7.0A

SMBJ7.0A

LH15-10C0512-02

470

120

120

SMBJ7.0A

SMBJ20A

SMBJ20A

LH15-10C0515-02

470

120

120

SMBJ7.0A

SMBJ20A

SMBJ20A

LH15-10C0524-01

470

120

120

SMBJ7.0A

SMBJ30A

SMBJ30A

LH15-10D0505-08

470

470

SMBJ7.0A

SMBJ7.0A

LH15-10D0512-04

470

220

SMBJ7.0A

SMBJ20A

LH15-10D0515-03

470

120

SMBJ7.0A

SMBJ20A

LH15-10D0524-02

470

47

SMBJ7.0A

SMBJ30A

LH20-10B03

330

SMBJ7.0A

LH20-10B05

330

SMBJ7.0A

LH20-10B09

220

SMBJ12A

LH20-10B12

220

SMBJ20A

LH20-10B15

220

SMBJ20A

LH20-10B24

220

SMBJ30A

LH20-10A05

470

470

SMBJ7.0A

SMBJ7.0A

LH20-10A12

120

120

SMBJ20A

SMBJ20A

LH20-10A15

68

68

SMBJ20A

SMBJ20A

LH20-10C0512-04

330

120

120

SMBJ7.0A

SMBJ20A

SMBJ20A

LH20-10C0515-03

330

120

120

SMBJ7.0A

SMBJ20A

SMBJ20A

LH20-10C0524-02

330

47

47

SMBJ7.0A

SMBJ30A

SMBJ30A

LH20-10D0512-06

330

220

SMBJ7.0A

SMBJ20A

LH20-10D0524-03

330

120

SMBJ7.0A

SMBJ30A

LH25-10B03

330

SMBJ7.0A

LH25-10B05

330

SMBJ7.0A

LH25-10B09

330

SMBJ12A

LH25-10B12

330

SMBJ20A

LH25-10B15

330

SMBJ20A

LH25-10B24

120

SMBJ30A

LH25-10B48

68

SMBJ64A

Note:

1. Output filtering capacitors C2, C4 and C6 are electrolytic capacitors, It is recommended to use high frequency and low impedance electrolytic capacitors. For

capacitance and current of capacitor please refer to manufacture

’s datasheet. Voltage derating of capacitor should be 80% or above. C1,C3,C5 are use to filter high

frequency noise，suggest choose 1

µF. TVS is recommended component to protect post-circuits (if converter fails). External input NTC is recommended to use 5D-9.

2. For standard EMC requirement, please refer to figure 1, figure 2, figure 3 or figure 4, if higher EMC requirement ,please refer to figure 6.

MOV: Varistor, model: 561KD14, it is used to protect the device under surge;

R1 、R2：2

Ω/3W Winding resistor；

R3：1M

Ω/2W；

CY1、CY2、CY3、CY4：102M/400VAC；

CX：224K/275VAC；

LCM：10mH-30mH；

FC-L01D：MORNSUN

’s 2KV/4KV Surge protector.

3. FUSE：LH05 recommended to use 1A/250V，LH10/LH15 recommended to use 2A/250V, LH20/LH25 recommended to use 3.15A/250V.

PCB MOUNTING WITH SOLDER PINS

A

D

8

7

6

5

4

1

2

3

Trim

3

7

6

5

4

1

2

8

Ф1.50[0.059]

3

7

6

5

4

1

2

8

Ф1.50[0.059]

3

8

7

6

5

4

1

2

Trim

Ф1.50[0.059]

3

7

6

5

4

1

2

8

Ф1.50[0.059]

Ф1.00[0.039]

Note:

Unit:mm[inch]

Pin length(H):

Pin

tolerances:

±0.10mm[±0.004inch]

General tolerances:

±0.50mm[±0.020inch]

diameter

L

5 series

H2

L 15 series

H

L

series

H10

L 05 series

H

(Main View)

(Bottom View)

No te: gri d2 .54 *2.54 mm.