REV. 0

AD8322

–4–

ORDERING GUIDE

Model

Temperature Range

Package Description

JA

Package Option

AD8322ARU

–40

°C to +85°C

28-Lead TSSOP

67.7

°C/W*

RU-28

AD8322ARU-REEL

–40

°C to +85°C

28-Lead TSSOP

67.7

°C/W*

RU-28

AD8322-EVAL

Evaluation Board

*Thermal Resistance measured on SEMI standard 4-layer board.

ABSOLUTE MAXIMUM RATINGS

*

Pins 6, 8, 9, 20, 21, 23, 27 . . . . . . . . . . . . . . . . . . . . . . . 6 V

Input Voltages

Pins 25, 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±0.5 V

Pins 1, 2, 3, 7 . . . . . . . . . . . . . . . . . . . . . . . –0.8 V to +5.5 V

Internal Power Dissipation

TSSOP (RU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.90 W

Operating Temperature Range . . . . . . . . . . . –40

°C to +85°C

Storage Temperature Range . . . . . . . . . . . . –65

°C to +150°C

Lead Temperature, Soldering 60 seconds . . . . . . . . . . . 300

°C

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the

device at these or any other conditions above those indicated in the operational

section of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

PIN CONFIGURATION

TOP VIEW

(Not to Scale)

28

27

26

25

24

23

22

21

20

19

18

17

16

15

1

2

3

4

5

6

7

8

9

10

11

12

13

14

AD8322

DATEN

GND

SDATA

VCC

CLK

VIN–

GND

VIN+

VCC

GND

PD

VCC

GND

GND

GND

VCC

VCC

VCC

VCC

GND

GND

GND

GND

GND

GND

OUT–

OUT+

BYP

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection. Although

the AD8322 features proprietary ESD protection circuitry, permanent damage may occur on

devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are

recommended to avoid performance degradation or loss of functionality.

WARNING!

ESD SENSITIVE DEVICE

PIN FUNCTION DESCRIPTIONS

Pin No.

Mnemonic

Description

1

SDATA

Serial Data Input. This digital input allows for an 8-bit serial (gain) word to be loaded into the internal

register with the MSB (Most Significant Bit) first.

2

CLK

Clock Input. The clock port controls the serial attenuator data transfer rate to the 8-bit master-slave

register. A Logic 0-to-1 transition latches the data bit and a 1-to-0 transfers the data bit to the slave.

This requires the input serial data word to be valid at or before this clock transition.

3

DATEN

Data Enable Low Input. This port controls the 8-bit parallel data latch and shift register. A Logic 0-to-1

transition transfers the latched data to the attenuator core (updates the gain) and simultaneously inhibits

serial data transfer into the register. A 1-to-0 transition inhibits the data latch (holds the previous gain

state) and simultaneously enables the register for serial data load.

4, 11, 12, 13,

GND

Common External Ground Reference.

14, 15, 16, 17,

18, 22, 24, 28

5

BYP

Internal Bypass. This pin must be externally ac-decoupled (0.1

µF capacitor).

6, 8, 9, 20,

VCC

Common Positive External Supply Voltage. A 0.1

µF capacitor must decouple each pin.

21, 23, 27

7

PD

Logic “0” powers down the part. Logic “1” powers up the part.

10

OUT–

Negative Output Signal.

19

OUT+

Positive Output Signal.

25

VIN+

termination.

26

VIN–