ADM222/ADM232A/ADM242

REV. 0

–7–

GENERAL INFORMATION

The ADM222/ADM232A/ADM242 are high speed RS-232

drivers/receivers requiring a single digital +5 V supply. The RS-

232 standard requires transmitters that will deliver

±5 V

minimum on the transmission channel and receivers that can

accept signal levels down to

±3 V. The parts achieve this by

integrating step up voltage converters and level shifting trans-

mitters and receivers onto the same chip. CMOS technology is

used to keep the power dissipation to an absolute minimum.

All devices contains an internal charge pump voltage doubler

and a voltage inverter that generates

±10 V from the +5 V

input. Four external 0.1

µF capacitors are required for the

internal charge pump voltage converter.

The ADM222/ADM232A/ADM242 is a modification, enhance-

ment and improvement to the AD230-AD241 family and

derivatives thereof. It is essentially plug-in compatible and does

not have materially different applications.

CIRCUIT DESCRIPTION

The internal circuitry consists of four main sections. These are:

A Charge Pump Voltage Converter

TTL/CMOS to RS-232 Transmitters

RS-232 to TTL/CMOS Receivers

Enable and Shutdown Functions.

Charge Pump DC-DC Voltage Converter

The Charge Pump Voltage converter consists of an oscillator

and a switching matrix. The converter generates a

±10 V supply

from the input 5 V level. This is done in two stages using a

switched capacitor technique. The 5 V input supply is doubled

to 10 V using capacitor C1 as the charge storage element. The

–10 V level is also generated from the input 5 V supply using C1

and C2 as the storage elements.

Capacitors C3 and C4 are used to reduce the output ripple.

Their values are not critical and can be reduced if higher levels

of ripple are acceptable. The charge pump capacitors C1 and

C2 may also be reduced at the expense of higher output

impedance on the V+ and V– supplies.

The V+ and V– supplies may also be used to power external

circuitry if the current requirements are small. Please refer to

the typical performance characteristics which shows the V+, V–

output voltage vs. current.

In the shutdown mode the charge pump is disabled and V+

decays to V

Transmitter (Driver) Section

The Drivers convert TTL/CMOS input levels into RS-232

output levels. With V

load, the output voltage swing is

±9 V. Even under worst case

conditions the drivers are guaranteed to meet the

±5 V RS-232

minimum requirement.

The input threshold levels are both TTL and CMOS compat-

ible with the switching threshold set at V

V

inputs may be left unconnected, as an internal 400 k

Ω pull- up

resistor pulls them high forcing the outputs into a low state.

As required by the RS-232 standard, the slew rate is limited to

less than 30 V/

µs without the need for an external slew limiting

capacitor, and the output impedance in the power-off state is

greater than 300

Ω.

Receiver Section

The receivers are inverting level shifters which accept RS-232

input levels (

±3 V to ±15 V) and translate them into 5 V TTL/

CMOS levels. The inputs have internal 5 k

Ω pull-down resistors

to ground and are also protected against overvoltages of up to

±30 V. The guaranteed switching thresholds are 0.8 V mini-

mum and 2.4 V maximum which are well within the

±3 V RS-

232 requirement. The low level threshold is deliberately positive

as it ensures that an unconnected input will be interpreted as a

low level.

The receivers have Schmitt trigger input with a hysteresis level

of 0.5 V. This ensures error free-reception for both noisy inputs

and for inputs with slow transition times

Enable and Shutdown Functions

On the ADM222, both receivers are fully disabled during

shutdown.

On the ADM242, both receivers continue to operate normally.

This function is useful for monitoring activity so that when it

occurs, the device can be taken out of the shutdown mode.

The ADM242 also contains a receiver enable function (EN)

which can be used to fully disable the receivers, independent of

SHDN

.

APPLICATIONS INFORMATION

A selection of typical operating circuits is shown in Figures 13

to 19.

Figure 19. Transmitter Output Disable Timing

10

90

100

0%

5V

A1

5µS

2.0V

5V