Electronic Components Datasheet Search |
|
ADM8696AN Datasheet(PDF) 6 Page - Analog Devices |
|
ADM8696AN Datasheet(HTML) 6 Page - Analog Devices |
6 / 12 page ADM8696/ADM8697 REV. 0 –6– Table I. ADM8696, ADM8697 Reset Pulse Width and Watchdog Timeout Selections Watchdog Timeout Period Reset Active Period OSC SEL OSC IN Normal Immediately After Reset Low External Clock Input 1024 CLKS 4096 CLKS 512 CLKS Low External Capacitor 400 ms × C/47 pF 1.6 s × C/47 pF 200 ms × C/47 pF Floating or High Low 100 ms 1.6 s 50 ms Floating or High Floating or High 1.6 s 1.6 s 50 ms NOTE With the OSC SEL pin low, OSC IN can be driven by an external clock signal, or an external capacitor can be connected between OSC IN and GND. The nominal internal oscillator frequency is 10.24 kHz. The nominal oscillator frequency with external capacitor is: F OSC (Hz) = 184,000/C (pF). WDI t 1 = RESET TIME t 2 = NORMAL (SHORT) WATCHDOG TIMEOUT PERIOD t 3 = WATCHDOG TIMEOUT PERIOD IMMEDIATELY FOLLOWING A RESET t 1 WDO RESET t 2 t 3 t 1 t 1 Figure 3. Watchdog Timeout Period and Reset Active Time The watchdog timeout period defaults to 1.6 s and the reset pulse width defaults to 50 ms, but these times to be adjusted as shown in Table I. Figure 4 shows the various oscillator configu- rations that can be used to adjust the reset pulse width and watchdog timeout period. The internal oscillator is enabled when OSC SEL is high or floating. In this mode, OSC IN selects between the 1.6 second and 100 ms watchdog timeout periods. In either case, immedi- ately after a reset the timeout period is 1.6 s. This gives the mi- croprocessor time to reinitialize the system. If OSC IN is low, the 100 ms watchdog period becomes effective after the first transition of WDI. The software should be written such that the I/O port driving WDI is left in its power-up reset state until the initialization routines are completed and the microprocessor is able to toggle WDI at the minimum watchdog timeout period of 70 ms. OSC IN OSC SEL ADM869x CLOCK 0 TO 500kHz 7 8 Figure 4a. External Clock Source COSC OSC IN OSC SEL ADM869x 7 8 Figure 4b. External Capacitor NC NC OSC IN OSC SEL ADM869x 7 8 Figure 4c. Internal Oscillator (1.6 s Watchdog) NC OSC IN OSC SEL ADM869x 7 8 Figure 4d. Internal Oscillator (100 ms Watchdog) Watchdog Output ( WDO) The Watchdog Output WDO provides a status output that goes low if the watchdog timer “times out” and remains low until set high by the next transition on the watchdog input. WDO is also set high when LLIN goes below the reset threshold. |
Similar Part No. - ADM8696AN |
|
Similar Description - ADM8696AN |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |