 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
ADSP-2186KST-160 Datasheet(PDF) 8 Page - Analog Devices |
|
||||||||||||||||||||||||||||||
ADSP-2186KST-160 Datasheet(HTML) 8 Page - Analog Devices |
|
|
8 / 36 page  ADSP-2186 –8– REV. A There are 8K words of memory accessible internally when the PMOVLAY register is set to 0. When PMOVLAY is set to some- thing other than 0, external accesses occur at addresses 0x2000 through 0x3FFF. The external address is generated as shown in Table II. Table II. PMOVLAY Addressing PMOVLAY Memory A13 A12:0 0 Internal Not Applicable Not Applicable 1 External 13 LSBs of Address Overlay 1 0 Between 0x2000 and 0x3FFF 2 External 13 LSBs of Address Overlay 2 1 Between 0x2000 and 0x3FFF NOTE: Addresses 0x2000 through 0x3FFF should not be accessed when PMOVLAY = 0. This organization provides for two external 8K overlay segments using only the normal 14 address bits, which allows for simple program overlays using one of the two external segments in place of the on-chip memory. Care must be taken in using this overlay space in that the processor core (i.e., the sequencer) does not take into account the PMOVLAY register value. For example, if a loop operation is occurring on one of the external overlays and the program changes to another external overlay or internal memory, an incorrect loop operation could occur. In addition, care must be taken in interrupt service routines as the overlay registers are not automatically saved and restored on the processor mode stack. When Mode B = 1, booting is disabled and overlay memory is disabled (PMOVLAY must be 0). Figure 5 shows the memory map in this configuration. RESERVED 0x3FFF 0x2000 0x1FFF 8K EXTERNAL 0x0000 PROGRAM MEMORY ADDRESS Figure 5. Program Memory (Mode B = 1) Data Memory The ADSP-2186 has 8160 16-bit words of internal data memory. In addition, the ADSP-2186 allows the use of 8K external memory overlays. Figure 6 shows the organization of the data memory. EXTERNAL 8K (DMOVLAY = 1, 2) INTERNAL 8160 WORDS DATA MEMORY ADDRESS 32 MEMORY– MAPPED REGISTERS 0x3FFF 0x3FEO 0x3FDF 0x2000 0x1FFF 0x0000 Figure 6. Data Memory There are 8160 words of memory accessible internally when the DMOVLAY register is set to 0. When DMOVLAY is set to something other than 0, external accesses occur at addresses 0x0000 through 0x1FFF. The external address is generated as shown in Table III. Table III. Addressing DMOVLAY Memory A13 A12:0 0 Internal Not Applicable Not Applicable 1 External 13 LSBs of Address Overlay 1 0 Between 0x0000 and 0x1FFF 2 External 13 LSBs of Address Overlay 2 1 Between 0x0000 and 0x1FFF This organization allows for two external 8K overlays using only the normal 14 address bits. All internal accesses complete in one cycle. Accesses to external memory are timed using the wait states specified by the DWAIT register. I/O Space (Full Memory Mode) The ADSP-2186 supports an additional external memory space called I/O space. This space is designed to support simple con- nections to peripherals or to bus interface ASIC data registers. I/O space supports 2048 locations. The lower eleven bits of the external address bus are used; the upper three bits are unde- fined. Two instructions were added to the core ADSP-2100 Family instruction set to read from and write to I/O memory space. The I/O space also has four dedicated three-bit wait state registers, IOWAIT0-3, that specify up to seven wait states to be automatically generated for each of four regions. The wait states act on address ranges as shown in Table IV. Table IV. Address Range Wait State Register 0x000–0x1FF IOWAIT0 0x200–0x3FF IOWAIT1 0x400–0x5FF IOWAIT2 0x600–0x7FF IOWAIT3 Composite Memory Select (CMS) The ADSP-2186 has a programmable memory select signal that is useful for generating memory select signals for memories mapped to more than one space. The CMS signal is generated to have the same timing as each of the individual memory select signals (PMS, DMS, BMS, IOMS), but can combine their functionality. Each bit in the CMSSEL register, when set, causes the CMS signal to be asserted when the selected memory select is as- serted. For example, to use a 32K word memory to act as both program and data memory, set the PMS and DMS bits in the CMSSEL register and use the CMS pin to drive the chip select of the memory and use either DMS or PMS as the additional address bit. The CMS pin functions as the other memory select signals, with the same timing and bus request logic. A 1 in the enable bit causes the assertion of the CMS signal at the same time as the selected memory select signal. All enable bits, except the BMS bit, default to 1 at reset. |
Similar Part No. - ADSP-2186KST-160 |
|
Similar Description - ADSP-2186KST-160 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
