Electronic Components Datasheet Search |
|
LP3982ILD-3.3 Datasheet(PDF) 10 Page - Texas Instruments |
|
LP3982ILD-3.3 Datasheet(HTML) 10 Page - Texas Instruments |
10 / 23 page LP3982 SNVS185D – FEBRUARY 2002 – REVISED APRIL 2013 www.ti.com Input Capacitor The LP3982 requires a minimum input capacitance of about 1 μF. The value may be increased indefinitely. The type is not critical to stability. However, instability may occur with bench set-ups where long supply leads are used, particularly at near dropout and high current conditions. This is attributed to the lead inductance coupling to the output through the gate oxide of the pass transistor; thus, forming a pseudo LCR network within the Loop- gain. A 10 μF tantalum input capacitor remedies this non-situ condition; its larger ESR acts to dampen the pseudo LCR network. This may only be necessary for some bench setups. 1 μF ceramic input capacitor are fine for most end-use applications. If a tantalum input capacitor is intended for the final application, it is important to consider their tendency to fail in short circuit mode, thus potentially damaging the part. Noise Bypass Capacitor The noise bypass capacitor (CC) significantly reduces output noise of the LP3982. It connects between pin 6 and ground. The optimum value for CC is 33 nF. Pin 6 directly connects to the high impedance output of the bandgap. The DC leakage of the CC capacitor should be considered; loading down the reference will reduce the output voltage. NPO and COG ceramic capacitors typically offer very low leakage. Polypropylene and polycarbonate film carbonate capacitor offer even lower leakage currents. CC does not affect the transient response; however, it does affect turn-on time. The smaller the CC value, the quicker the turn-on time. Power Dissipation Power dissipation refers to the part's ability to radiate heat away from the silicon, with packaging being a key factor. A reasonable analogy is the packaging a human being might wear, a jacket for example. A jacket keeps a person comfortable on a cold day, but not so comfortable on a hot day. It would be even worse if the person was exerting power (exercising). This is because the jacket has resistance to heat flow to the outside ambient air, like the IC package has a thermal resistance from its junctions to the ambient ( θJA). θJA has a unit of temperature per power and can be used to calculate the IC's junction temperature as follows: TJ = θJA (PD) + TA • TJ is the junction temperature of the IC • θJA is the thermal resistance from the junction to the ambient air outside the package • PD is the power exerted by the IC • TA is the ambient temperature (4) PD is calculated as follows: PD = IOUT (VIN -VO) • θJA for the LP3982 package (VSSOP-8) is 223°C/W with no forced air flow • 182°C/W with 225 linear feet per minute (LFPM) of air flow • 163°C/W with 500 LFPM of air flow • 149°C/W with 900 LFPM of air flow (5) θJA can also be decreased (improved) by considering the layout of the PC board: heavy traces (particularly at VIN and the two VOUT pins), large planes, through-holes, etc. Improvements and absolute measurements of the θJA can be estimated by utilizing the thermal shutdown circuitry that is internal to the IC. The thermal shutdown turns off the pass transistor of the device when its junction temperature reaches 160°C (Typical). The pass transistor doesn't turn on again until the junction temperature drops about 10°C (hysteresis). Using the thermal shutdown circuit to estimate , θJA can be done as follows: With a low input to output voltage differential, set the load current to 300 mA. Increase the input voltage until the thermal shutdown begins to cycle on and off. Then slowly decrease VIN (100 mV increments) until the part stays on. Record the resulting voltage differential (VD) and use it in the following equation: 10 Submit Documentation Feedback Copyright © 2002–2013, Texas Instruments Incorporated Product Folder Links: LP3982 |
Similar Part No. - LP3982ILD-3.3 |
|
Similar Description - LP3982ILD-3.3 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |