235

Text

234

Text

Surface-Mounting Signal Relay – G6S

Maximum Switching Power

Single-winding Latching

Double-winding Latching

Switching voltage (V)

Ambient temperature (

°C)

Ambient Temperature vs.

Maximum Coil Voltage

Single-side Stable

Ambient temperature (

°C)

G6SU

G6SK

12 VDC

max.

G6SK

24 VDC

AC resistive load

DC resistive load

12 VDC max.

24 VDC

(G6S-Y, 12 VDC max.)

Reference Data

Ambient Temperature vs. Switching Current

Single-side Stable

Single-winding Latching

Double-winding Latching

Ambient temperature (

°C)

G6SU

12 VDC max.

G6SU

24 VDC

G6SK

12 VDC max.

G6SK

24 VDC

Ambient temperature (

°C)

12 VDC max.

24 VDC

(G6S-Y)

24 VDC

(G6S-Y, 12 VDC

max.)

24 VDC

(G6S-Y)

Note: The maximum coil voltage refers to the maximum value in a varying range of

operating power voltage, not a continuous voltage.

Engineering Data

Soldering

Preheating

Upper surface of case (peak):

255∞C max.

120 max.

30 max

250 max.

230

180

150

Relay

terminal

section

Soldering

Preheating

220 to

245

180 to

200

150

90 to 120

20 to 30

Temperatures indicate the surface temperatures of the PCB.

• The thickness of cream solder to be applied should be within a

range between 150 and 200 µm on OMRON’s recommended

PCB pattern.

• In order to perform correct soldering, it is recommended that the

correct soldering conditions be maintained as shown below on

the left side.

Note: The temperature profile indicates the temperature of the

relay terminal section.

Recommended Soldering Method

1. IRS Method (Mounting solder: Lead)

2. IRS Method (Mounting solder: Lead-free)

Time (s)

Time (s)

Surface-Mounting Signal Relay – G6S

Model

Contact form

Coil ratings

Contact ratings

G6S-2, G6S-2F, G6S-2G

DPDT

1.5 to 48 VDC

G6SU2, G6SK-2, G6SU-2F

1.5 to 24 VDC

G6SU2G, G6SK-2F, G6SK-2G

■

Approved Standards

UL (File No. E41515)/CSA C22.2 (File No. LR24825)

2 A, 30 VDC

0.3 A, 110 VDC

0.5 A, 125 VAC

Model

Contact form

Isolation category

Voltage

G6S-2-Y, G6S-2G-Y, G6S-2F-Y

DPDT

Supplementary Isolation

250 VAC

EN60950

■

Characteristics

Contact resistance (Note)

75 mΩ max.

Operate (set) time (Note 2)

4 ms max. (mean value: approx. 2.5 ms; latching type: approx. 2 ms)

Release (reset) time (Note 2)

4 ms max. (mean value: approx. 1.5 ms; latching type: approx. 2 ms)

Max. operating frequency

Mechanical: 36,000 operations/hr

Electrical: 1,800 operations/hr (under rated load)

Insulation resistance (Note 3)

1,000 MΩ min. (at 500 VDC)

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min between coil and contacts

1,000 VAC, 50/60 Hz for 1 min between coil and contacts (double-winding latching)

1,500 VAC, 50/60 Hz for 1 min between contacts of different polarity

1,000 VAC, 50/60 Hz for 1 min between contacts of same polarity

500 VAC, 50/60 Hz for 1 min between set and reset coil (double-winding latching)

Impulse withstand voltage

2,500 V (2 x 10 µs) between coil and contacts

1,500 V (10 x 160 µs) between coil and contacts (double-winding latching)

2,500 V (2 x 10 µs) between contacts of different polarity

1,500 V (10 x 160 µs) between contacts of same polarity (conforms to FCC Part 68)

Vibration resistance

Destruction: 10 to 55 to 10 Hz, 2.5mm single amplitude (5mm double amplitude)

Malfunction: 10 to 55 to 10 Hz, 1.65mm single amplitude (3.3mm double amplitude)

Shock resistance

Endurance

Mechanical: 100,000,000 operations min. (at 36,000 operations/hr)

Electrical: 100,000 operations min. (2 A at 30 VDC, resistive load: 1,200 operations/hr)

100,000 operations min. (0.5 A at 125 VAC, resistive load)

Ambient temperature

Operating: -40˚C to 85˚C (with no icing), -40˚C to 70˚C (double-winding latching, 24 VDC)

Ambient humidity

Operating: 5% to 85%

Weight

Approx. 2 g

Note: The above values are initial values.

Note: 1. The contact resistance was measured with 10mA at 1 VDC with a voltage drop method.

Note: 2. Values in parentheses are actual values.

Note: 3. The insulation resistance was measured with a 500-VDC megohmeter applied to the same parts as those used for checking

the dielectric strength (except between the set and reset coil).

Omron 08 Cat 1-302

5/10/07

15:39

Page 234