Electronic Components Datasheet Search |
|
SP6644 Datasheet(PDF) 11 Page - Sipex Corporation |
|
SP6644 Datasheet(HTML) 11 Page - Sipex Corporation |
11 / 15 page 11 Date: 11/30/04 SP6644/6645 High Efficiency Boost Regulator © Copyright 2004 Sipex Corporation With an external resistor tolerance of +1%, the peak current tolerance will be +6%. To make sure that the SP6644/6645 internal circuitry adequately controls the inductor current, it is recommended that values equal to or greater than 22 µH (+10%) be used. The SP6644/6645 devices control algorithm delivers an average maximum load current in regulation as defined by: where I LOAD-MAX [A] is the maximum load current, E is the efficiency factor (generally between 0.8 and 0.9), I PEAK [A] is the programmed peak inductor current, V BATT [V] is the input voltage to the device, and V OUT [V] is the output voltage. Given the minimum input voltage, output voltage, and maximum average load current, the value of I PEAK can be solved for and an appropriate inductor can be chosen. It is good design practice to use the lowest peak current possible to reduce possible EMI and output ripple voltage. A closed-core inductor, such as a toroid or shielded bobbin, will minimize any fringe magnetic fields or EMI. Figure 28. Adjustable Output Voltage Circuitry APPLICATION NOTES Printed circuit board layout is a critical part of design. Poor designs can result in excessive EMI on the voltage gradients and feedback paths on the ground planes with applications involving high switching frequencies and large peak currents. Excessive EMI can result in instability or regulation errors. All power components should be placed on the PC board as closely as possible with the traces kept short, direct, and wide (>50mils or 1.25mm). Extra copper on the PC board should be integrated into ground as a pseudo-ground plane. On a multilayer PC board, route the star ground using component-side copper fill, then connect it to the internal ground plane using vias. For the SP6644/6645 devices, the inductor and input and output filter capacitors should be soldered with their ground pins as close together as possible in a star-ground configuration. The V OUT pin must be bypassed directly to ground as close to the SP6644/6645 devices as possible (within 0.2in or 5mm). The DC-DC converter and any digital circuitry should be placed on the opposite corner of the PC board as far away from sensitive RF and analog input stages. The external voltage-feedback network should be placed very close to the FB pin as well as the R LIM resistor (within 0.2in or 5mm). Any GND VOUT FB LX VBATT 47µF 0.1µF 22µF RLIM VOUT= 2V to 5.2V SHDN 0.88V to 3.3V Input SP6644 SP6645 100pF* R1 R2 *optional compensation 22µH 0.7A BATTLO I LOAD-MAX = E x I PEAK x VBATT 2 x V OUT |
Similar Part No. - SP6644_05 |
|
Similar Description - SP6644_05 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |