 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
SMG.10.20 Datasheet(PDF) 4 Page - List of Unclassifed Manufacturers |
|
||||||||||||||||||||||||||||||
SMG.10.20 Datasheet(HTML) 4 Page - List of Unclassifed Manufacturers |
|
|
4 / 28 page  axial 0.09 0.10 0.12 0.15 0.18 0.20 radial 0.03 0.04 0.05 0.06 0.08 0.09 SELECTION bearing clearances The clearances in rod ends and spherical bearings are related to size, as indicated in the following table. In all cases, the clearances indicated are the maximum to be expected. * * * * * * * * * SMG, SFG SMG.10, SFG.10 SMG.20, SFG.20 SMG.40, SFG.40 SMG.45, SFG.45 SMGM.50/51/52 SMEM.50/51/52 SMVV, SFVV SME, SFE SME.40, SFE.40 SME.45, SFE.45 SS SS.10 SS.45 SSA SSA.10 SSA.45 SSA.50 SSVV SSE SSE.45 SSE.50 Table 2 Excellent, very well suited to indicated conditions. Average Not recommended for indicated conditions Self-lubricating - maintenance free key * Table 2 compares various types of rod end and spherical bearings under different operating conditions, and will enable an initial selection to be made. Size and load considerations should then be checked by reference to the product tables on the following pages. The suitability and life expectancy of the chosen component can be checked by calculation if required; please contact the Huco sales office for assistance. 1 2 3 4 5 6 7 8 9 10 11 1 2 5 12 13 14 15 8 9 11 16 static loads The product tables on the following pages refer to axial and radial static loads. The loads indicated are the maximum allowable. safety factor The allowable static loads given in our tables have been determined by dividing the static load at failure by 2.5 Maximum allowable load = load at failure 2.5 Axial and Radial static loads are defined in the following diagrams. axial static loads Allowable axial loads are not stated for rod ends as in most circumstances the limiting condition will be determined not by the strength of the head, but by the resistance of the shank to bending. Where significant, axial loads should be determined and referred to us for advice. This table does not apply to the types listed below which are produced with minimum clearance to provide a tight fit. SMG.40, SFG.40 SMEM.50/51/52 SMGM.50/51/52 SMVV, SFVV SSA.50 SME, SFE SME.40, SFE.40 SSVV SSE SSE.50 Radial static loads Axial static loads Clearance mm 2 – 68 – 12 14 – 18 20 – 22 25 – 30 35 – 50 28 Tel: +44 (0)1992 509888 ® 4 |
Similar Part No. - SMG.10.20 |
|
Similar Description - SMG.10.20 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
